HEAp–SiCp/7075Al 复合材料的搅拌摩擦加工制备及性能研究

左立生 ,  陈志伟 ,  陶华书 ,  薛朝阳 ,  张兴权 ,  左敦稳

安徽工业大学学报(自然科学版) ›› 2026, Vol. 43 ›› Issue (5) : 565 -574.

PDF (33633KB)
安徽工业大学学报(自然科学版) ›› 2026, Vol. 43 ›› Issue (5) : 565 -574. DOI: 10.12415/j.issn.1671−7872.26114
智能冶金与先进材料 • 先进金属材料设计与制造专刊

HEAp–SiCp/7075Al 复合材料的搅拌摩擦加工制备及性能研究

作者信息 +

Research on the Preparation and Properties of HEAp–SiCp/7075Al Composite Materials by Friction Stir Processing

Author information +
文章历史 +
PDF (34439K)

摘要

采用多道次搅拌摩擦加工工艺,制备不同 SiC 含量的高熵合金颗粒–碳化硅颗粒增强 7075 铝基 (HEAp–SiCp/7075Al) 复合材料,研究 SiC 含量对其成形质量、界面特征、力学性能及摩擦磨损行为的影响,优化 7075Al 合金的综合性能。结果表明:SiC 质量分数为 2% 时,增强颗粒在焊核区分散均匀,与基体界面结合致密;质量分数增至 5% 和 10% 后,颗粒团聚加剧,均匀性显著下降。显微硬度随 SiC 含量增加呈升高趋势,2%,5% 和 10% 试样焊核区平均硬度分别为 150.97,160.96,163.71 HV。拉伸性能变化规律则与之相反,2% 试样极限抗拉强度最优,达 416.5 MPa,归因于高含量下团聚加重。断口分析表明,复合材料呈韧–脆混合断裂模式,随 SiC 含量增加,主导机制由颗粒断裂逐渐转为界面脱黏与团聚。摩擦磨损性能随 SiC 含量提升而显著改善,10% 试样磨痕最浅,耐磨性最佳。综上,增强颗粒的分散均匀性对力学性能调控作用显著,适量 SiC 与高熵合金协同增强可实现强度与耐磨性的协同优化。本研究为高熵合金颗粒增强铝基复合材料的成分优化与工艺设计提供了实验依据与理论参考。

Abstract

To optimize the mechanical and tribological properties of 7075Al alloy, a multi-pass friction stir processing technique was employed to fabricate HEAp–SiCp/7075Al composites with varying SiC particle contents. The influence of SiC content on the forming quality, interfacial characteristics, mechanical properties, and tribological behavior of the composites was investigated. The results indicate that at a SiC mass fraction of 2%, the reinforcing particles are uniformly dispersed in the nugget zone and tightly bonded to the matrix interface. With increasing SiC content, agglomeration becomes more severe and dispersion uniformity decreases. Microhardness exhibits an increasing trend with SiC content, with average nugget-zone hardness values reaching 150.97 HV, 160.96 HV, and 163.71 HV for the 2%, 5%, and 10% SiC specimens, respectively. In contrast, the tensile properties show the opposite trend;the 2% SiC specimen exhibits the best ultimate tensile strength of 416.5 MPa, attributed to aggravated agglomeration at higher contents. Fracture analysis reveals a ductile-brittle mixed mode, and as the SiC content increases, the dominant fracture mechanism shifts from particle fracture to interfacial debonding and agglomeration. Tribological performance significantly improves with the increase in SiC content, with the 10% SiC specimen exhibiting the smallest wear scar depth and the best wear resistance. Overall, the uniform dispersion of reinforcing particles plays a significant role in tuning the mechanical properties, and the synergistic reinforcement of an appropriate amount of SiC and high-entropy alloy (HEA) enables a comprehensive improvement in both strength and wear resistance of the composite. These findings provide experimental evidence and theoretical guidance for the composition optimization and process design of HEA particle-reinforced aluminum matrix composites.

关键词

搅拌摩擦加工 / 复合材料 / 高熵合金 / 微观组织 / 力学性能 / 摩擦性能

Key words

friction stir processing / composite materials / high-entropy alloys / microstructure / mechanical properties / friction performance

引用本文

引用格式 ▾
左立生,陈志伟,陶华书,薛朝阳,张兴权,左敦稳. HEAp–SiCp/7075Al 复合材料的搅拌摩擦加工制备及性能研究[J]. 安徽工业大学学报(自然科学版), 2026, 43(5): 565-574 DOI:10.12415/j.issn.1671−7872.26114

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

龙飞, 刘瞿, 朱艺星, 等. 搅拌摩擦加工改性 Mg−5Zn 合金的显微组织与耐腐蚀性能[J]. 金属学报, 2025, 61(7): 1071-1081.

[2]

LONG F, LIU Q, ZHU Y X, et al. Microstructure and corrosion resistance of modified Mg−5Zn alloy via friction stir processing[J]. Acta Metallurgica Sinica, 2025, 61(7): 1071-1081.

[3]

XIA C C, LI X B, LIU X C, et al. Achieving near—net—forming of in—situ fabricated SiCp/2024Al composites with high performance by friction stir channeling assisted stationary shoulder friction stir processing[J]. Tribology International, 2026, 219: 111786.

[4]

MISHRA R S, MA Z Y, CHARIT I. Friction stir processing: a novel technique for fabrication of surface composite[J]. Materials Science and Engineering: A, 2003, 341(1/2): 307-310.

[5]

DEORE H A, BHARDWAJ A, RAO A G, et al. Consequence of reinforced SiC particles and post process artificial ageing on microstructure and mechanical properties of friction stir processed AA7075[J]. Defence Technology, 2020, 16(5): 1039-1050.

[6]

SRIVASTAVA A K, MAURYA N K, DIXIT A R, et al. Experimental investigations of A359/Si3N4 surface composite produced by multi—pass friction stir processing[J]. Materials Chemistry and Physics, 2021, 257: 123717.

[7]

MEHTA K M, BADHEKA V J. Wear behavior of Al−6061−B4C surface composites fabricated by friction stir processing using slot and hole method of reinforcement application[J]. Wear, 2023, 522: 204719.

[8]

DEVARAJU A, KUMAR A, KUMARASWAMY A, et al. Influence of reinforcements (SiC and Al2O3) and rotational speed on wear and mechanical properties of aluminum alloy 6061−T6 based surface hybrid composites produced via friction stir processing[J]. Materials and Design, 2013, 51: 331-341.

[9]

DEVARAJU A, KUMAR A, KOTIVEERACHARI B. Influence of addition of Grp/Al2O3p with SiCp on wear properties of aluminum alloy 6061−T6 hybrid composites via friction stir processing[J]. Transactions of Nonferrous Metals Society of China, 2013, 23(5): 1275-1280.

[10]

LU T W, CHEN W P, WANG P, et al. Enhanced mechanical properties and thermo—physical properties of 7075Al hybrid composites reinforced by the mixture of Cr particles and SiCp[J]. Journal of Alloys and Compounds, 2018, 735: 1137-1144.

[11]

LU T W, HE T B, LI Z X, et al. Microstructure, mechanical properties and machinability of particulate reinforced Al matrix composites: a comparative study between SiC particles and high—entropy alloy particles[J]. Journal of Materials Research and Technology, 2020, 9(6): 13646-13660.

[12]

LU T W, SCUDINO S, CHEN W P, et al. The influence of nanocrystalline CoNiFeAl0.4Ti0.6Cr0.5 high—entropy alloy particles addition on microstructure and mechanical properties of SiCp/7075Al composites[J]. Materials Science and Engineering: A, 2018, 726: 126-136.

[13]

MARODE R V, LEMMA T A, PEDAPATI S R, et al. Investigation of thermo—mechanical characteristics in friction stir processing of AZ91 surface composite: novel study through SPH analysis[J]. Lubricants, 2025, 13(10): 450.

[14]

WANG Y, CHEN Y H, XIE J L, et al. High entropy alloy reinforced aluminum matrix composites prepared by novel rotation friction extrusion process: microstructure and mechanical properties[J]. Materials Science and Engineering: A, 2022, 854: 143789.

[15]

LI J C, LI Y L, WANG F F, et al. Friction stir processing of high—entropy alloy reinforced aluminum matrix composites for mechanical properties enhancement[J]. Materials Science and Engineering: A, 2020, 792: 139755.

[16]

WANG W, FANG Y, PENG P, et al. Microstructure, mechanical and wear properties of AZ31/CoCrFeNi composites fabricated by friction stir processing[J]. Transactions of Nonferrous Metals Society of China, 2023, 33(8): 2328-2339.

[17]

YANG X, ZHAI X, DONG P, et al. Interface characteristics of high—entropy alloy/Al−Mg composites by underwater friction stir processing[J]. Materials Letters, 2020, 275: 128200.

[18]

邱丰, 佟昊天, 沈平, 等. 综述: SiC/Al 界面反应与界面结构演变规律及机制[J]. 金属学报, 2019, 55(1): 87-100. QIU F,

[19]

TONG H T, SHEN P, et al. Overview: SiC/Al interface reaction and interface structure evolution mechanism[J]. Acta Metallurgica Sinica, 2019, 55(1): 87-100.

[20]

ADABIFIROOZJAEI E, RASTKERDAR E, NEMOTO Y, et al. In—situ scanning transmission electron microscopy study of Al—amorphous SiO2 layer—SiC interface[J]. Journal of Materials Science, 2023, 58: 2456-2468.

[21]

柳培, 王爱琴, 郝世明, 等. SiCp/2024Al 基复合材料的界面行为[J]. 电子显微学报, 2014, 33(4): 306-312.

[22]

LIU P, WANG A Q. HAO S M, et al. The interfacial condition of SiCp /Al composites[J]. Journal of Chinese Electron Microscopy Society, 2014, 33(4): 306-312.

[23]

JAMALI A, MIRSALEHI S E. Investigation on effects of traverse speed and number of passes on mechanical and abrasive properties of AA7075−T6/ZrO2 surface nanocomposite produced using friction stir processing[J]. Welding in the World, 2022, 66: 297-313.

[24]

RAJAN G, KUMAR A, MULA S. Influence of friction stir processing on wear behavior of nanosized SiC reinforced AA5083 nanocomposites developed by stir casting[J]. Journal of Manufacturing Processes, 2025, 141: 1631-1649.

[25]

FENG A H, CHEN D L, MA Z Y. Microstructure and cyclic deformation behavior of a friction—stir—welded 7075 Al alloy[J]. Metallurgical and Materials Transactions A, 2010, 41: 957-971.

[26]

LIU Z Y, WANG Q Z, XIAO B L, et al. Experimental and modeling investigation on SiCp distribution in powder metallurgy processed SiCp/2024 Al composites[J]. Materials Science and Engineering: A, 2010, 527(21/22): 5582-5591.

[27]

NIYAZ A B M, NAVEEN K S H, KALLIMANI A S, et al. Mechanical properties of SiC nanoparticle—reinforced Al−2024 alloy[J]. Fracture and Structural Integrity: International Journal of Italian Group of Fracture, 2025, 19(72): 148-161.

[28]

SHIN S, PARK H, PARK B, et al. Dispersion mechanism and mechanical properties of SiC reinforcement in aluminum matrix composite through stir— and die—casting processes[J]. Applied Sciences, 2021, 11(3): 952.

[29]

LI P, TONG Y Q, WANG X X, et al. Microstructures and mechanical properties of AlCoCrFeNi2.1/6061−T6 aluminum—matrix composites prepared by friction stir processing[J]. Materials Science and Engineering: A, 2023, 863: 144544.

[30]

YANG X, YAN Z F, DONG P, et al. Surface modification of aluminum alloy by incorporation of AlCoCrFeNi high entropy alloy particles via underwater friction stir processing[J]. Surface and Coatings Technology, 2020, 385: 125438.

[31]

WANG Y, CHEN Y H, XIE J L, et al. Microstructure and mechanical properties of CrMnFeCoNi high entropy alloy/Al composite with different reinforcement content[J]. Journal of Alloys and Compounds, 2023, 960: 170882.

[32]

LI P B, CHEN T J. Effect of SiCp volume fraction on the microstructure and tensile properties of SiCp/2024 Al—based composites prepared by powder thixoforming[J]. Journal of Materials Research, 2016, 31: 2850-2862.

[33]

NAJAR F A, RATHEE S, SRIVASTAVA M, et al. Enhancement of tribological, mechanical and fluidic characteristics of Al5059/B4C+5%Mg surface composites using friction stir processing[J]. Tribology International, 2026, 217: 111648.

[34]

HE X J, YU X F, ZHAO D C, et al. Simultaneous enhancement of strength, ductility and wear resistance in Al5052 alloy via hybrid in—situ Al3Ni and nano—SiC reinforcement during friction stir processing[J]. Ceramics International, 2026, 52(14): 25597-25611.

[35]

SUN H Q, SHI Y N, ZHANG M X. Wear behaviour of AZ91D magnesium alloy with a nanocrystalline surface layer[J]. Surface and Coatings Technology, 2007, 202(13): 2859-2864.

[36]

KARABACAK A H, ÇANAKÇI A, ÖZKAYA S, et al. Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal—metal composites[J]. Journal of Alloys and Compounds, 2024, 1008: 176627.

基金资助

安徽省自然科学基金项目(2308085ME165)

AI Summary AI Mindmap
PDF (33633KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉