超高强度汽车钢强韧化协同提升机理研究进展

龙勇 ,  陈其伟 ,  王子健 ,  朱国辉 ,  丁汉林

安徽工业大学学报(自然科学版) ›› 2026, Vol. 43 ›› Issue (5) : 522 -534.

PDF (12656KB)
安徽工业大学学报(自然科学版) ›› 2026, Vol. 43 ›› Issue (5) : 522 -534. DOI: 10.12415/j.issn.1671−7872.26133
智能冶金与先进材料 • 先进金属材料设计与制造专刊

超高强度汽车钢强韧化协同提升机理研究进展

作者信息 +

Research Progress on Synergistic Strengthening-toughening Mechanism of Ultra-high-strength Automotive Steels

Author information +
文章历史 +
PDF (12959K)

摘要

超高强度汽车钢的强韧化协同提升是实现汽车轻量化与安全性的核心路径。本文系统综述了四类典型第三代超高强度汽车钢 (QP 钢、中锰钢、22MnB5 热冲压钢及 Mn–Cr 系低合金钢) 的组织设计策略与力学性能特征,重点剖析其强韧化机理的异同。研究表明:QP 钢依托马氏体相变与碳配分工艺稳定残余奥氏体,可实现强度与塑性的较好匹配,但其强塑积水平仍相对有限;中锰钢借助奥氏体逆相变及 Mn 与 C 元素配分,获得较高含量的残余奥氏体,显著提升塑性延伸能力,但屈服强度偏低;22MnB5 钢经热冲压成形后形成全马氏体组织,呈现超高强度,但塑性储备明显不足。上述三类钢的性能优化分别受限于残余奥氏体稳定性不足、合金化成本较高及全马氏体组织固有低塑性等瓶颈。相比之下,Mn–Cr 系钢采用低合金化设计,通过多相组织调控、细晶强化及第二相弥散析出与位错的交互作用,在极少含甚至不含残余奥氏体的条件下,实现了超高强度与良好塑性的匹配。该思路为新型超高强度汽车钢的合金设计与强韧化机理创新应用提供了科学参考。

Abstract

The synergistic enhancement of strength and toughness in ultra-high-strength automotive steels is a key approach to achieving both vehicle lightweighting and safety. This review systematically summarizes the microstructural design strategies and mechanical-property characteristics of four representative types of third-generation ultra-high-strength automotive steels, namely QP steels, medium-Mn steels, 22MnB5 hot-stamped steels, and Mn–Cr low-alloy steels, with particular emphasis on the similarities and differences in their strengthening and toughening mechanisms. The results show that QP steels stabilize retained austenite through martensitic transformation and carbon partitioning, thereby achieving a favorable combination of high strength and ductility, although their product of strength and elongation remains relatively limited. Medium-Mn steels obtain a relatively high fraction of retained austenite through austenite-reverted transformation and Mn/C partitioning, which markedly enhances tensile ductility, whereas their yield strength remains comparatively low. After hot stamping, 22MnB5 steels develop a fully martensitic microstructure and exhibit ultra-high strength, but their ductility reserve is clearly insufficient. Further optimization of these three steel systems is constrained, respectively, by insufficient retained-austenite stability, relatively high alloying costs, and the intrinsically low ductility of fully martensitic microstructures. In contrast, Mn–Cr steels adopt a low-alloy design strategy and achieve a favorable combination of ultra-high strength and good ductility, even with little or no retained austenite, through the synergistic effects of multiphase microstructural control, grain-refinement strengthening, dispersed second-phase precipitation, and interactions between precipitates and dislocations. This strategy provides a scientific basis for the alloy design of novel ultra-high-strength automotive steels and for the development of innovative strengthening and toughening approaches.

关键词

第三代汽车钢 / QP 钢 / 中锰钢 / 热冲压 / Mn–Cr 钢 / 强韧化机理

Key words

third-generation automotive steel / QP steel / medium-Mn steel / hot stamping / Mn–Cr steel / strengthening and toughening mechanism

引用本文

引用格式 ▾
龙勇,陈其伟,王子健,朱国辉,丁汉林. 超高强度汽车钢强韧化协同提升机理研究进展[J]. 安徽工业大学学报(自然科学版), 2026, 43(5): 522-534 DOI:10.12415/j.issn.1671−7872.26133

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

范子杰, 桂良进, 苏瑞意. 汽车轻量化技术的研究与进展[J]. 汽车安全与节能学报, 2014, 5(1): 1-16.

[2]

FAN Z J, GUI L J, SU R Y. Research and development of automotive lightweight technology[J]. Journal of Automotive Safety and Energy, 2014, 5(1): 1-16.

[3]

康永林. 汽车轻量化先进高强钢与节能减排[J]. 钢铁, 2008, 43(6): 1-7.

[4]

KANG Y L. Lightweight vehicle, advanced high strength steel and energy—saving and emission reduction[J]. Iron and Steel, 2008, 43(6): 1-7.

[5]

王利, 杨雄飞, 陆匠心. 汽车轻量化用高强度钢板的发展[J]. 钢铁, 2006, 41(9): 1-8.

[6]

WANG L, YANG X F, LU J X. Development of high strength steel sheets for lightweight automobile[J]. Iron and Steel, 2006, 41(9): 1-8.

[7]

李扬, 刘汉武, 杜云慧, 等. 汽车用先进高强钢的应用现状和发展方向[J]. 材料导报 A: 综述篇, 2011, 25(7): 101-104.

[8]

LI Y, LIU H W, DU Y H, et al. Applications and developments of AHSS in automobile industry[J]. Materials Review A: Review Papers, 2011, 25(7): 101-104.

[9]

TAUB A, DE MOOR E, LUO A, et al. Materials for automotive lightweighting[J]. Annual Review of Materials Research, 2019, 49: 327-359.

[10]

CZERWINSKI F. Current trends in automotive lightweighting strategies and materials[J]. Materials, 2021, 14: 6631.

[11]

李倩, 陈晨, 李艳国, 等. 汽车用先进高强度中锰钢研究进展[J]. 燕山大学学报, 2025, 49(1): 1-9.

[12]

LI Q, CHEN C, LI Y G, et al. Research progress of advanced high—strength medium—Mn steel for automobiles[J]. Journal of Yanshan University, 2025, 49(1): 1-9.

[13]

BOUAZIZ O, ZUROB H, HUANG M. Driving force and logic of development of advanced high strength steels for automotive applications[J]. Steel Research International, 2013, 84(10): 937-947.

[14]

ZHAO J, JIANG Z. Thermomechanical processing of advanced high strength steels[J]. Progress in Materials Science, 2018, 94: 174-242.

[15]

SCHMITT J H, IUNG T. New developments of advanced high—strength steels for automotive applications[J]. Comptes Rendus Physique, 2018, 19(8): 641-656.

[16]

赵征志, 陈伟健, 高鹏飞, 等. 先进高强度汽车用钢研究进展及展望[J]. 钢铁研究学报, 2020, 32(12): 1059-1076

[17]

ZHAO Z Z, CHEN W J, GAO P F, et al. Research progress and prospect of advanced high—strength automotive steels[J]. Journal of Iron and Steel Research, 2020, 32(12): 1059-1076.

[18]

BLECK W, GUO X, MA Y. The TRIP effect and its application in cold formable sheet steels[J]. Steel Research International, 2017, 88(10): 1700218.

[19]

SOLEIMANI M, KALHOR A, MIRZADEH H. Transformation—induced plasticity (TRIP) in advanced steels: a review[J]. Materials Science and Engineering A, 2020, 795: 140023.

[20]

吝章国. 先进高强度汽车用钢板研究进展与技术应用现状[J]. 河北冶金, 2016(1): 1-7.

[21]

LIN Z G. Research progress and present technique application situation of advanced high—strength automobile steel sheet[J]. Hebei Metallurgy, 2016(1): 1-7.

[22]

闫翠, 李麟, 符仁钰, 等. TRIP 钢的研究进展[J]. 上海金属, 2008, 30(4): 40-44.

[23]

YAN C, LI L, FU R Y, et al. A review on research progress of TRIP steel[J]. Shanghai Metals, 2008, 30(4): 40-44.

[24]

唐代明. TRIP 钢中合金元素的作用和处理工艺的研究进展[J]. 钢铁研究学报, 2008, 20(1): 1-5.

[25]

TANG D M. Review of alloying elements and processing of TRIP steels[J]. Journal of Iron and Steel Research, 2008, 20(1): 1-5.

[26]

CHEN H, ZHAO L, LU S, et al. Progress and perspective of ultra—high—strength martensitic steels for automobile[J]. Metals, 2022, 12: 2184.

[27]

CHOI J H, JO M C, LEE H, et al. Cu addition effects on TRIP to TWIP transition and tensile property improvement of ultra—high—strength austenitic high—Mn steels[J]. Acta Materialia, 2019, 166: 246-260.

[28]

SPEER J G, MATLOCK D K, DE COOMAN B C, et al. Carbon partitioning into austenite after martensite transformation[J]. Acta Materialia, 2003, 51(9): 2611-2622.

[29]

KARBASIAN H, TEKKAYA A E. A review on hot stamping[J]. Journal of Materials Processing Technology, 2010, 210: 2103-2118.

[30]

徐祖耀. 用于超高强度钢的淬火−碳分配−回火 (沉淀) 工艺[J]. 热处理, 2008, 23(2): 1-5.

[31]

XU Z Y. Quenching−partitioning−tempering (precipitation) process for ultra—high strength steel[J]. Heat Treatment, 2008, 23(2): 1-5.

[32]

徐祖耀. 淬火−碳分配−回火 (Q−P−T) 工艺浅介[J]. 金属热处理, 2009, 34(6): 1-8.

[33]

XU Z Y. A brief introduction to quenching−partitioning−tempering (Q−P−T) process[J]. Heat Treatment of Metals, 2009, 34(6): 1-8.

[34]

王昌, 徐海峰, 黄崇湘, 等. 中锰钢逆相变退火组织的演变及锰的配分行为[J]. 钢铁研究学报, 2016, 28(4): 38-46.

[35]

WANG C, XU H F, HUANG C X, et al. Evolution of ART—annealed microstructure and partition behavior of manganese in medium manganese steel[J]. Journal of Iron and Steel Research, 2016, 28(4): 38-46.

[36]

王存宇, 曹文全, 董瀚. 中锰第三代汽车钢及其先进性[C]// 第十一届中国钢铁年会论文集. 北京: 中国金属学会, 2017: 1-6.

[37]

WANG C Y, CAO W Q, DONG H. The third generation automobile steel of medium manganese and its advantages[C]// Proceedings of the 11th China Steel Annual Conference. Beijing: CSM, 2017: 1-6.

[38]

朱国明, 康永林, 朱帅. 汽车用超高强 QP 钢的工艺与组织性能研究[J]. 机械工程学报, 2017, 53(12): 110-117.

[39]

ZHU G M, KANG Y L, ZHU S. Study on process, microstructure and property of ultra—high strength QP steel for automobile[J]. Journal of Mechanical Engineering, 2017, 53(12): 110-117.

[40]

SANTOFIMIA M J, SPEER J G, CLARKE A J, et al. Influence of interface mobility on the evolution of austenite—martensite grain assemblies during annealing[J]. ActaMaterialia, 2009, 57: 4548-4557.

[41]

CLARKE A J, SPEER J G, MILLER M K, et al. Carbon partitioning to austenite from martensite or bainite during the quench and partition (QP) process: a critical assessment[J]. Acta Materialia, 2008, 56(1): 16-22.

[42]

高学然, 陈晓虎, 原思宇, 等. 汽车用 Q&P 钢的研究进展[J]. 金属热处理, 2023, 48(7): 245-253.

[43]

GAO X R, CHEN X H, YUAN S Y, et al. Research progress of Q&P steel for automobiles[J]. Heat Treatment of Metals, 2023, 48(7): 245-253.

[44]

梁校, 罗平, 李贤君, 等. Q&P 工艺对 22MnB5 钢微观组织及力学性能的影响[J]. 金属热处理, 2020, 45(7): 57-62.

[45]

LIANG X, LUO P, LI X J, et al. Effect of Q&P process on microstructure and mechanical properties of 22MnB5 steel[J]. Heat Treatment of Metals, 2020, 45(7): 57-62.

[46]

SEO E J, CHO L, ESTRIN Y, et al. Microstructure—mechanical properties relationships for quenching and partitioning (Q&P) processed steel[J]. Acta Materialia, 2016, 113: 124-139.

[47]

XIONG X C, CHEN B, HUANG M X, et al. The effect of morphology on the stability of retained austenite in a quenched and partitioned steel[J]. Scripta Materialia, 2013, 68(5): 321-324.

[48]

BAI S B, CHEN Y A, SHENG J, et al. A comprehensive overview of high strength and toughness steels for automobile based on QP process[J]. Journal of Materials Research and Technology, 2023, 27: 2216-2236.

[49]

DE MOOR E, LACROIX S, CLARKE A J, et al. Effect of retained austenite stabilized via quench and partitioning on the strain hardening of martensitic steels[J]. Metallurgical and Materials Transactions A, 2008, 39: 2586-2595.

[50]

SANTOFIMIA M J, NGUYEN−MINH T, ZHAO L, et al. New low carbon Q&P steels containing film—like intercritical ferrite[J]. Materials Science and Engineering A, 2010, 527: 6429-6439.

[51]

SANTOFIMIA M J, ZHAO L, PETROV R, et al. Characterization of the microstructure obtained by the quenching and partitioning process in a low—carbon steel[J]. Materials Characterization, 2008, 59: 1758-1764.

[52]

KÄHKÖNEN M J, DE MOOR E, SPEER J G, et al. Carbon and manganese effects on quenching and partitioning response of CMnSi—steels[J]. SAE International Journal of Materials and Manufacturing, 2015, 8: 419-424.

[53]

易红亮, 赵明辉, 王睿婷, 等. 1 800 MPa 级以上高强钢的研究现状[J]. 东北大学学报 (自然科学版), 2025, 46(8): 1-16.

[54]

YI H L, ZHAO M H, WANG R T, et al. Current status of research on high—strength steel above 1 800 MPa grade[J]. Journal of Northeastern University (Natural Science), 2025, 46(8): 1-16.

[55]

齐加胜, 徐文权. 汽车用中锰钢的研究现状与展望[J]. 金属热处理, 2025, 50(3): 244-249.

[56]

QI J S, XU W Q. Research status and prospects of medium manganese steels for automobiles[J]. Heat Treatment of Metals, 2025, 50(3): 244-249.

[57]

MOHAPATRA S, SATPATHY B, SARKAR A, et al. Recent advances in medium—manganese steel: a review of key findings, challenges, and future perspectives[J]. Journal of Materials Science, 2025, 60: 9447-9528.

[58]

ZHANG M H, LI L F, DING J, et al. Temperature—dependent micromechanical behavior of medium—Mn transformation—induced—plasticity steel studied by in situ synchrotron X ray diffraction[J]. Acta Materialia, 2017, 141: 294-303.

[59]

ZHENG G, LI X, CHANG Y, et al. A comparative study on formability of the third—generation automotive medium—Mn steel and 22MnB5 steel[J]. Journal of Materials Engineering and Performance, 2018, 27: 530-540.

[60]

KWIATKOWSKI DA SILVA A, INDEN G, KUMAR A, et al. Competition between formation of carbides and reversed austenite during tempering of a medium—manganese steel studied by thermodynamic—kinetic simulations and atom probe tomography[J]. Acta Materialia, 2018, 147: 165-175.

[61]

HE B B, HU B, YEN H W, et al. High dislocation density—induced large ductility in deformed and partitioned steels[J]. Science, 2017, 357: 1029-1032.

[62]

SOHN S S, SONG H, JO M C, et al. Novel 1.5 GPa—strength with 50%—ductility by transformation—induced plasticity of non—recrystallized austenite in duplex steels[J]. Scientific Reports, 2017, 7: 1255.

[63]

LU Q, EIZADJOU M, WANG J, et al. Medium—Mn martensitic steel ductilized by baking[J]. Metallurgical and Materials Transactions A, 2019, 50: 4067-4074.

[64]

徐娟萍, 付豪, 王正, 等. 中锰钢的研究进展与前景[J]. 工程科学学报, 2019, 41(5): 557-572.

[65]

XU J P, FU H, WANG Z, et al. Research progress and prospect of medium manganese steel[J]. Chinese Journal of Engineering, 2019, 41(5): 557-572.

[66]

ZHANG Y, YE Q, YAN Y. Processing, microstructure, mechanical properties, and hydrogen embrittlement of medium—Mn steels: a review[J]. Journal of Materials Science & Technology, 2024, 201: 44-57.

[67]

LI S S, LUO H W. Medium—Mn steels for hot forming application in the automotive industry[J]. International Journal of Minerals, Metallurgy and Materials, 2021, 28(5): 741-753.

[68]

张宜生, 王子健, 王梁. 高强钢热冲压成形工艺及装备进展[J]. 塑性工程学报, 2018, 25(5): 11-23.

[69]

ZHANG Y S, WANG Z J, WANG L. Progress in hot stamping process and equipment for high strength steel sheet[J]. Journal of Plasticity Engineering, 2018, 25(5): 11-23.

[70]

CHANG Z Y, LI Y J, WU D. Enhanced ductility and toughness in 2 000 MPa grade press hardening steels by auto—tempering[J]. Materials Science and Engineering A, 2020, 784: 139342.

[71]

CAVUSOGLU O, CAVUSOGLU O, YILMAZOGLU A G, et al. Microstructural features and mechanical properties of 22MnB5 hot stamping steel in different heat treatment conditions[J]. Journal of Materials Research and Technology, 2020, 9(5): 10901-10908.

[72]

CHEN W J, GAO P F, WANG S, et al. Strengthening mechanisms of Nb and V microalloying high strength hot—stamped steel[J]. Materials Science and Engineering A, 2020, 797: 140115.

[73]

HOU Z R, OPITZ T, XIONG X C, et al. Bake—partitioning in a press—hardening steel[J]. Scripta Materialia, 2019, 162: 492-496.

[74]

李彦泽, 李运刚, 任喜强, 等. 汽车用高强钢氢脆损伤研究的现状[J]. 上海金属, 2024, 46(1): 1-8.

[75]

LI Y Z, LI Y G, REN X Q, et al. Present situation of research on hydrogen embrittlement damage of high strength steel for automobile[J]. Shanghai Metals, 2024, 46(1): 1-8.

[76]

周雨婷, 栾道成, 樊华, 等. 汽车用高强钢及其焊接研究进展[J]. 焊接技术, 2025, 54(10): 1-6.

[77]

ZHOU Y T, LUAN D C, FAN H, et al. Research progress of automotive high—strength steel and its welding[J]. Welding Technology, 2025, 54(10): 1-6.

[78]

YOO J, JO M C, JO M C, et al. Effects of solid solution and grain—boundary segregation of Mo on hydrogen embrittlement in 32MnB5 hot—stamping steels[J]. Acta Materialia, 2021, 207: 116661.

[79]

CHEN Y S, LU H, LIANG J T, et al. Observation of hydrogen trapping at dislocations, grain boundaries, and precipitates[J]. Science, 2020, 367: 171-175.

[80]

SHI R J, MA Y, WANG Z D, et al. Atomic—scale investigation of deep hydrogen trapping in NbC/α−Fe semi—coherent interfaces[J]. Acta Materialia, 2020, 200: 686-698.

[81]

DJUKIC M B, BAKIC G M, SIJACKI ZERAVCIC V, et al. The synergistic action and interplay of hydrogen embrittlement mechanisms in steels and iron: localized plasticity and decohesion[J]. Engineering Fracture Mechanics, 2019, 216: 106528.

[82]

洪松, 丁汉林, 朱国辉, 等. 热处理工艺对 20Mn2Cr 汽车用钢热轧板组织和性能的影响[J]. 安徽工业大学学报 (自然科学版), 2018, 35(3): 202-208.

[83]

HONG S, DING H L, ZHU G H, et al. Effect of heat treatment process on microstructure and properties of hot rolled sheet of automobile steel 20Mn2Cr[J]. Journal of Anhui University of Technology (Natural Science), 2018, 35(3): 202-208.

[84]

洪松. 超高强度 20Mn2Cr 汽车用钢多相组织调控的实验研究[D]. 马鞍山: 安徽工业大学, 2018.

[85]

HONG S. Experimental study on the design of multi—phase microstructures for 20Mn2Cr ultra—high strength automobile steel[D]. Maanshan: Anhui University of Technology, 2018.

[86]

陈健, 黄飞, 丁汉林, 等. 热处理对超高强度 20Mn2Cr 汽车钢组织和性能的影响[J]. 材料热处理学报, 2021, 42(7): 89-97.

[87]

CHEN J, HUANG F, DING H L, et al. Effect of heat treatment on microstructure and mechanical properties of ultra—high strength 20Mn2Cr automobile steel[J]. Transactions of Materials and Heat Treatment, 2021, 42(7): 89-97.

[88]

陈健. 超高强度 20Mn2Cr 汽车钢塑性提升研究[D]. 马鞍山: 安徽工业大学, 2021.

[89]

CHEN J. Study on the Enhancement of Plasticity of Ultra—high Strength 20Mn2Cr Automobile Steel[D]. Maanshan: Anhui University of Technology, 2021.

[90]

黄文静, 陈健, 裘欣, 等. 时效处理对超高强度 20Mn2Cr 汽车钢组织性能的影响[J]. 钢铁研究学报, 2024, 36(5): 627-639.

[91]

HUANG W J, CHEN J, QIU X, et al. Effect of aging treatment on microstructure and mechanical properties of ultra—high strength 20Mn2Cr automotive steel[J]. Journal of Iron and Steel Research, 2024, 36(5): 627-639.

[92]

RAABE D, PONGE D, DMITRIEVA O, et al. Nanoprecipitate—hardened 1.5 GPa steels with unexpected high ductility[J]. Scripta Materialia, 2009, 60: 1141-1144.

[93]

PENG S, WEI Y, GAO H. Nanoscale precipitates as sustainable dislocation sources for enhanced ductility and high strength[J]. Proceedings of the National Academy of Sciences of the United States of America, 2020, 117(10): 5204-5209.

[94]

张志建, 陈刚, 刘志桥, 等. Nb−Ti 低合金高强钢第二相析出及其对力学性能的影响[J]. 上海金属, 2018, 40(6): 12-18.

[95]

ZHANG Z J, CHEN G, LIU Z Q, et al. Second phase precipitation and its effect on the mechanical properties of Nb−Ti microalloyed HSLA steels[J]. Shanghai Metals, 2018, 40(6): 12-18.

[96]

XIAO F R, CAO Y B, QIAO G Y, et al. Effect of Nb solute and NbC precipitates on dynamic or static recrystallization in Nb steels[J]. Journal of Iron and Steel Research International, 2012, 19: 52-56.

[97]

齐佳林, 魏扬华, 朱国辉, 等. 连退和时效温度对新型 24Mn2CrNb 汽车用钢的组织和性能的影响[J]. 材料热处理学报, 2022, 43(7): 92-100.

[98]

QI J L, WEI Y H, ZHU G H, et al. Effect of continuous annealing and aging temperature on microstructure and mechanical properties of new 24Mn2CrNb automobile steel[J]. Transactions of Materials and Heat Treatment, 2022, 43(7): 92-100.

[99]

黄文静. 24Mn2CrNb 强韧化机理及柔性化应用[D]. 马鞍山: 安徽工业大学, 2024.

[100]

HUANG W J. Strengthening and Toughening Mechanism of 24Mn2CrNb and Flexible Application[D]. Maanshan: Anhui University of Technology, 2024.

基金资助

国家自然科学基金项目(52174367)

AI Summary AI Mindmap
PDF (12656KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉