Ar-O2 二元保护气中氧含量对碳钢MAG 焊接质量的影响

任小佳 ,  张栋梁 ,  石磊 ,  沈威

现代工业与技术 ›› 2026, Vol. 3 ›› Issue (2) : 22 -25.

PDF (1551KB)
现代工业与技术 ›› 2026, Vol. 3 ›› Issue (2) : 22 -25. DOI: 10.12349/mit.v3i2.11063

Ar-O2 二元保护气中氧含量对碳钢MAG 焊接质量的影响

作者信息 +

Effect of Oxygen Content in Ar-O₂ Binary Shielding Gas on MAG Welding Quality of Carbon Steel

Author information +
文章历史 +
PDF (1587K)

摘要

采用CLOOS QRC350焊接机器人配合福尼斯TPS500i焊机,系统研究了不同氧含量(2%、5%、12%)的Ar-O₂二元保护气体与20%CO₂+80%Ar混合气体对3 mm碳钢Q345E薄板MAG焊接质量的影响。通过视频采集监测焊接过程,结合焊缝表面形貌、宏观金相及七项综合指标评价,对比分析了角接和对接两种焊接形式下的焊接质量。结果表明,随氧含量增加,焊接过程稳定性及焊缝成形呈先改善后劣化的趋势。5%O₂+95%Ar综合性能最优,操控性、外观质量及烟尘飞溅控制均达优秀水平,显著优于CO₂体系。CO₂在薄板对接焊中因宽弧特性具有熔透优势,而Ar-O₂体系飞溅少、结晶物少,但氧含量过低易产生指状熔深,过高则导致熔池过度氧化。5%O₂+95%Ar可作为替代传统CO₂混合气体的较优方案。

Abstract

The effects of Ar-O₂ binary shielding gases with different oxygen contents (2%, 5%, and 12%) and a conventional 20%CO₂+80%Ar mixture on the MAG welding quality of 3 mm Q345E carbon steel thin plates were systematically investigated using a CLOOS QRC350 welding robot combined with a Fronius TPS500i power source. The welding process was monitored via video recording, and the welding quality under fillet and butt joint configurations was comparatively analyzed in terms of weld surface appearance, macroscopic metallography, and a seven-criterion comprehensive evaluation system. The results indicate that with increasing oxygen content, both the welding process stability and weld bead appearance exhibit an initial improvement followed by deterioration. The 5%O₂+95%Ar mixture achieves the optimal overall performance, with operability, surface quality, and spatter and fume control all rated as excellent, significantly outperforming the CO₂-based shielding gas. Owing to its wide-arc characteristics, the CO₂-based mixture demonstrates superior penetration in thin-plate butt welding, whereas the Ar-O₂ system produces less spatter and fewer surface crystallites. However, excessively low oxygen content tends to cause finger-like penetration, while excessively high oxygen content leads to over-oxidation of the weld pool. The 5%O₂+95%Ar mixture can serve as a promising alternative to the conventional CO₂-based shielding gas for carbon steel thin-plate MAG welding.

关键词

MAG / Ar-O2保护气 / 氧含量 / 焊接质量 / 碳钢

Key words

MAG / Ar-O₂ shielding gas / oxygen content / welding quality / carbon steel

引用本文

引用格式 ▾
任小佳,张栋梁,石磊,沈威. Ar-O2 二元保护气中氧含量对碳钢MAG 焊接质量的影响[J]. 现代工业与技术, 2026, 3(2): 22-25 DOI:10.12349/mit.v3i2.11063

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

裘荣鹏, 武丹. 保护气体中氧气含量对低合金高强钢熔敷金属组织和力学性能的影响[J]. 热加工工艺, 2016, 45(23): 52-55+ 59.

[2]

王文, 薛小怀, 等. 保护气体对440 MPa HSLA钢GMAW焊缝组织及韧性的影响[J]. 焊接学报, 2013, 34(5): 89-92.

[3]

许鸿吉, 等. 低合金高强钢针状铁素体组织特征和形成机理[J]. 钢铁研究学报, 2015, (5): 1-6.

AI Summary AI Mindmap
PDF (1551KB)

14

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉