西藏某矿山采场充填体原位取芯质量评价
In-situ coring quality evaluation of stope backfill in a mine in Xizang
以国内某大型铜多金属矿的分段凿岩阶段空场嗣后充填开采工艺为背景,以一步骤充填体为研究对象,通过对井下原位取芯的374 组试件进行强度测试,系统分析了灰砂比1∶4 和1∶6 两种充填体的强度分布规律。结果表明:灰砂比1∶4 充填体强度范围为1.24~6.11 MPa,平均强度为2.66 MPa;灰砂比1∶6 充填体强度范围为0.62~4.94 MPa,平均强度为2.46 MPa。两种配比充填体均表现出强度离散性大、整体均匀性较差的特点,反映出充填料浆在制备过程中工艺参数控制不够精确。扫描电镜微观分析表明,充填体强度主要来源于针棒状钙矾石形成的骨架结构及其中填充的C-S-H 凝胶。强度差异则与水化产物(钙矾石和C-S-H 凝胶)的生成量、未反应水含量以及孔隙率等因素相关。为提升充填质量,建议提高充填浓度,并确保胶凝材料下料的精确性与稳定性。
Based on the sublevel drilling and subsequent backfill mining method employed in a large copper polymetallic mine in China, this study focuses on the primary backfill body as the research subject. Through strength testing of 374 sets of specimens obtained via in-situ coring underground, the strength distribution patterns of backfill materials with cement-sand ratios of 1∶4 and 1∶6 were systematically analyzed. The results indicate that for the backfill with a cement-sand ratio of 1∶4, the strength ranges from 1.24 MPa to 6.11 MPa, with an average strength of 2.66 MPa. For the backfill with a cement-sand ratio of 1∶6, the strength ranges from 0.62 MPa to 4.94 MPa, with an average strength of 2.46 MPa. Both mix ratios exhibit significant strength variability and poor overall uniformity, reflecting imprecise control of process parameters during the preparation of the backfill slurry. Scanning electron microscopy (SEM) microanalysis reveals that the strength of the backfill primarily originates from the skeletal structure formed by needle-or rod-shaped ettringite crystals, filled with C-S-H gel. The differences in strength are related to factors such as the quantity of hydration products (ettringite and C-S-H gel), the content of unreacted water, and the porosity within the backfill. To improve backfill quality, it is recommended to increase the backfill concentration while ensuring precise and consistent dosing of cementitious materials.
| [1] |
杨小聪, 郭利杰. 尾矿和废石综合利用技术[M]. 北京: 化学工业出版社, 2018. |
| [2] |
|
| [3] |
郭利杰, 刘光生, 马青海, |
| [4] |
|
| [5] |
张雷, 郭利杰, 许文远, |
| [6] |
|
| [7] |
吴爱祥, 王洪江. 金属矿膏体充填理论与技术[M]. 北京: 科学出版社, 2015. |
| [8] |
|
| [9] |
李一帆, 张建明, 邓飞, |
| [10] |
|
| [11] |
郭利杰, 贾冲, 赵越, |
| [12] |
|
| [13] |
陈寅, 郭利杰, 魏晓明, |
| [14] |
|
| [15] |
李宗楠, 王果, 郭利杰. 原位充填体强度影响因素分析[J]. 有色金属(矿山部分), 2015, 67(增刊1): 31-34. |
| [16] |
|
| [17] |
杨云飞, 邓代强, 龙云刚, |
| [18] |
|
| [19] |
李欣, 郭利杰, 许文远, |
| [20] |
|
| [21] |
常悦, 赵志云, 王向玲, |
| [22] |
|
| [23] |
中华人民共和国住房和城乡建设部, 国家市场监督管理总局. 金属非金属矿山充填工程技术标准: GB/T 51450-2022[S]. 北京: 中国计划出版社, 2022-09-08. |
| [24] |
State Administration for Market Regulation, Ministry of Housing and Urban-Rural Development of the People's Republic of China. Technical standard for filling engineering of metal and nonmetal mines: GB/T 51450-2022[S]. Beijing: China Planning Press, 2022-09-08. |
| [25] |
孙德民, 任建平, 焦华喆, |
| [26] |
|
| [27] |
裴启涛. 影响胶结充填体质量的主要因素及控制措施[J]. 现代矿业, 2009(增刊1): 99-102. |
| [28] |
|
| [29] |
周礼, 林卫星, 欧任泽. 全粒级碎石胶结充填材料及泵送试验研究[J]. 黄金, 2017(6): 37-40. |
| [30] |
|
| [31] |
付毅, 王劼. 含C4A3S矿物硅酸盐水泥充填性能研究[J]. 矿冶, 2009, 18(4): 4-8. |
| [32] |
|
| [33] |
张雷, 郭利杰, 魏晓明, |
| [34] |
|
国家科技重大专项(2024ZD1003705)
矿冶科技集团有限公司青年创新基金滚动支持项目(04-2342)
/
| 〈 |
|
〉 |