HLS-J 模拟高地月壤真空烧结性能研究

苑浩轩 ,  王超 ,  贾永政 ,  张辉 ,  王哲 ,  王明涌

矿冶 ›› 2026, Vol. 35 ›› Issue (1) : 65 -74.

PDF (33135KB)
矿冶 ›› 2026, Vol. 35 ›› Issue (1) : 65 -74. DOI: 10.3969/j.issn.1005-7854.2026.01.010
冶金与材料

HLS-J 模拟高地月壤真空烧结性能研究

作者信息 +

Investigation on vacuum sintering properties of HLS-J simulated highland lunar soil

Author information +
文章历史 +
PDF (33929K)

摘要

月球基地建设对实现深空探测具有重要意义。鉴于地月运输成本高昂,利用月面本土资源的原位资源利用技术(ISRU)已成为月球基地建造的主要途径。本研究以HLS-J 模拟高地月壤为原料,在真空环境下分别于970 ℃、1 030 ℃和1 090 ℃条件下烧结,探讨不同烧结温度下HLS-J 模拟高地月壤复杂矿相的热力学行为对烧结试件的机械性能影响。采用X 射线衍射(XRD)分析矿物物相组成,扫描电子显微镜(SEM)观察微观形貌,结合粒径分析仪和差示扫描量热仪(DSC)对粉末粒径及热性能进行表征,并通过单轴压缩测试评估烧结试件的力学性能。结果表明,在970 ~ 1 090 ℃烧结试件致密度与抗压强度均显示了随烧结温度先升高后降低的变化趋势,当烧结温度为1 030 ℃时,烧结试件平均抗压强度高达108.64 MPa,对应的试件致密度最大(73.43%)。

Abstract

The construction of a lunar base plays a critical role in enabling deep-space exploration. Due to the high cost and logistical challenges associated with transporting materials from Earth to the Moon, in-situ resource utilization (ISRU) has emerged as a promising and practical approach for lunar base development. In this study, HLS-J highland lunar regolith simulant was used as the raw material to investigate its sintering behavior under vacuum conditions at three different temperatures: 970 ℃, 1 030 ℃, and 1 090 ℃. The effects of sintering temperature on the thermodynamic behavior, phase evolution, microstructure, and mechanical properties of the simulant were systematically examined. Characterization techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) were employed to analyze the phase composition, microstructural features, and thermal behavior of the sintered specimens. In addition, uniaxial compression tests were conducted to evaluate their mechanical performance. The results indicated that within the temperature range of 970–1 090 ℃, the density of the sintered specimens first increased and then decreased with rising temperature. The optimal sintering temperature was identified as 1 030 ℃, at which the specimens achieved a maximum average compressive strength of 108.64 MPa and the highest relative density of 73.43%.

关键词

模拟月壤 / 真空烧结 / 机械性能 / 微观结构 / 原位资源利用

Key words

simulated lunar soil / vacuum sintering / mechanical properties / microstructure / in-situ resource utilization

引用本文

引用格式 ▾
苑浩轩,王超,贾永政,张辉,王哲,王明涌. HLS-J 模拟高地月壤真空烧结性能研究[J]. 矿冶, 2026, 35(1): 65-74 DOI:10.3969/j.issn.1005-7854.2026.01.010

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

庞之浩. 嫦娥六号任务及我国未来探月前景[J]. 科学, 2024, 76(4): 16-22, 2, 69.

[2]

PANG Z H. Chang’e-6 mission and prospects of China's future lunar exploration[J]. Science, 2024, 76(4): 16-22, 2, 69.

[3]

童小华, 袁烽, 郑虎, 等. 月球资源勘测与原位利用进展及关键挑战[J]. 同济大学学报(自然科学版), 2024, 52(8): 1151-1162.

[4]

TONG X H, YUAN F, ZHENG H, et al. Progress and key challenges of lunar resource exploration and in-situ utilization[J]. Journal of Tongji University (Natural Science Edition), 2024, 52(8): 1151-1162.

[5]

DUKE M B, BLAIR B R, DIAZ J. Lunar resource utilization: implications for commerce and exploration[J]. Advances in Space Research, 2003, 31(11): 2413-2419.

[6]

SANDERS G, LARSON W, SACKSTEDER K, et al. NASA in-situ resource utilization (ISRU) project: Development and implementation[C]// Proceedings of the AIAA SPACE 2008 Conference & Exposition. San Diego, California, USA: American Institute of Aeronautics and Astronautics, 2008: 7853.

[7]

宋蕾, 徐佼, 唐红, 等. 模拟月壤成型研究现状[J]. 矿物学报, 2020, 40(1): 47-57.

[8]

SONG L, XU J, TANG H, et al. Research progress on the forming of simulated lunar regolith[J]. Acta Mineralogica Sinica, 2020, 40(1): 47-57.

[9]

宋蕾. 模拟月壤激光3D打印成型机理研究[D]. 重庆: 中国科学院大学(中国科学院重庆绿色智能技术研究院), 2019.

[10]

SONG L. Study on the laser 3D printing forming mechanism of simulated lunar regolith[D]. Chongqing: University of Chinese Academy of Sciences (Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences), 2019.

[11]

RAHAMAN M N. Sintering of Ceramics[M]. Boca Raton: CRC Press, 2007.

[12]

华建民, 肖畅, 薛暄译, 等. 辐射烧结硬化模拟月壤的物理和力学性能试验研究[J]. 土木与环境工程学报(中英文), 2025, 47(2): 13-19.

[13]

HUA J M, XIAO C, XUE X, et al. Experimental study on physical and mechanical properties of radiation-sintered hardened simulated lunar regolith[J]. Journal of Civil and Environmental Engineering (Chinese-English), 2025, 47(2): 13-19.

[14]

ZOCCA A, FATERI M, AL-SABBAGH D, et al. Investigation of the sintering and melting of JSC-2A lunar regolith simulant[J]. Ceramics International, 2020, 46(9): 14097-14104.

[15]

ZHOU S, LIN Z, TAO X, et al. Sintering of Chang 'e-5 high-fidelity lunar soil simulant for providing high-strength materials for lunar base construction[J]. Science China Technological Sciences, 2025, 68(8): 1820602.

[16]

SONG L, XU J, TANG H, et al. Vacuum sintering behavior and magnetic transformation for high-Ti type basalt simulated lunar regolith[J]. Icarus, 2020, 347: 113810.

[17]

DING M, CHEN X, LI Y, et al. Vacuum sintering of the self-developed Chang’E-5 lunar regolith simulant[J]. Construction and Building Materials, 2024, 438: 137343.

[18]

HAN W, DING L, CAI L, et al. Sintering of HUST-1 lunar regolith simulant[J]. Construction and Building Materials, 2022, 324: 126655.

[19]

石艳洁, 丁梦钊, 罗理达, 等. 真空条件下模拟月壤玻璃高温熔体的结构和性能[J/OL]. 东华大学学报(自然科学版), 1-7[2025-10-21]. https://doi.org/10.19886/j.cnki.dhdz.2024.0313.

[20]

SHI Y J, DING M Z, LUO L D, et al. Structure and properties of high-temperature melt of simulated lunar regolith glass under vacuum[J/OL]. Journal of Donghua University (Natural Science Edition), 1-7[2025-10-21]. https://doi.org/10.19886/j.cnki.dhdz.2024.0313.

[21]

ANNELL C, CARRON M, CHRISTIAN R, et al. Chemical and spectrographic analyses of lunar samples from Apollo 12 mission[J]. Geological Survey Research, 1971, 179-181.

[22]

RYDER G, SCHURAYTZ B C. Chemical variation of the large Apollo 15 olivine-normative mare basalt rock samples[J]. Journal of Geophysical Research: Planets, 2001, 106(E1): 1435-1451.

[23]

TEAM A P E. Apollo 17 lunar samples: chemical and petrographic description[J]. Science, 1973, 182(4113): 659-672.

[24]

WIIK H, MAXWELL J, BOUVIER J-L. Chemical composition of some Apollo 14 lunar samples[J]. Earth and Planetary Science Letters, 1973, 17(2): 365-368.

[25]

TEAM A P E. The Apollo 16 lunar samples: petrographic and chemical description[J]. Science, 1973, 179(4068): 23-34.

[26]

SUN X, ZHANG R, LI X, et al. JLU-H: a novel lunar highland regolith simulant for use in large-scale engineering experiments[J]. Planetary and Space Science, 2022, 221: 105562.

[27]

XU X, HUI H, CHEN W, et al. Formation of lunar highlands anorthosites[J]. Earth and Planetary Science Letters, 2020, 536: 116-138.

[28]

TAYLOR A, PIETERS C, PATCHEN A, et al. Mineralogical and chemical characterization of lunar highland soils: Insights into the space weathering of soils on airless bodies[J]. Journal of Geophysical Research: Planets, 2010, 115: E2002.

[29]

MEURISSE A, BELTZUNG J, KOLBE M, et al. Influence of mineral composition on sintering lunar regolith[J]. Journal of Aerospace Engineering, 2017, 30(4): 04017014.

[30]

RICKMAN D L, ARCHER P D, KOVTUN R N, et al. Characterization of NUW-LHT-5m, a lunar highland simulant[J]. Technical Publication, 2024, NASA/TP-20240007991.

[31]

FULCHIHNONI M, FUNICIELLO R, TADDEUCCI A, et al. Glassy spheroids in lunar fines from Apollo 12 samples 12070, 37; 12001, 73; and 12057, 60[C]// Proceedings of the Lunar Science Conference. Vol. 2. Houston, TX: Lunar Science Institute, 1971: 937.

[32]

MCKAY D, BOGARD D, MORRIS R, et al. Apollo 16 regolith breccias: characterization and evidence for early formation in the mega-regolith[J]. Journal of Geophysical Research: Solid Earth, 1986, 91(B4): 277-303.

[33]

LIU Y, PARK J, SCHENARE D, et al. Characterization of lunar dust for toxicological studies. Ⅱ: Texture and shape characteristics[J]. Journal of Aerospace Engineering, 2008, 21(4): 272-279.

[34]

LAUL J, PAPIKE J, SIMON S. The lunar regolith-Comparative studies of the Apollo and Luna sites. Chemistry of soils from Apollo 17, Luna 16, 20, and 24[C]// Proceedings of the In: Lunar and Planetary Science Conference, 12th, Houston, TX, March 16-20, 1981, Proceedings Section 1(A82-31677 15-91) New York and Oxford, Pergamon Press, 1982: 389.

[35]

SLABIC A, GRUENER J E, KOVTUN N, et al. Lunar regolith simulant user's guide: revision[J/OL]. National Aeronautics and Space Administration (2024-01-17)[2025-09-05]. https://ntrs.nasa.gov/citations/20240011783.

[36]

STREET J, KENNETH W, RAY C, RCICKMAN D, et al. Thermal properties of lunar regolith simulants[J]. In: Earth and Space 2010: Engineering, Science, Construction, and Operations in Challenging Environments. 2010, 41096(366): 266-275.

[37]

GOLDSMITH J R. The melting and breakdown reactions of anorthite at high pressures and temperatures[J]. American Mineralogist, 1980, 65(3/4): 272-284.

[38]

FRRIZZO G, ZACCARON A, DE SOUZA NANDI V, et al. Pyroplasticity on porcelain tiles of the albite-potassium feldspar-kaolin system: a mixture design analysis[J]. Journal of Building Engineering, 2020, 31: 101432.

[39]

SIGHINOLFI D. Experimental study of deformations and state of tension in traditional ceramic materials[J]. Materiały Ceramiczne, 2011, 63: 226-232.

[40]

GARCIA-TEN J, SABURIT A, BERNAEDO E, et al. Development of lightweight porcelain stoneware tiles using foaming agents[J]. Journal of the European Ceramic Society, 2012, 32(4): 745-752.

[41]

SONG L, XU J, FAN S, et al. Vacuum sintered lunar regolith simulant: pore-forming and thermal conductivity[J]. Ceramics International, 2019, 45(3): 3627-3633.

[42]

LIM S, DEGLI-ALESSANDRNI G, BOWEN J, et al. The microstructure and mechanical properties of microwave-heated lunar simulants at different input powers under vacuum[J]. Scientific reports, 2023, 13(1): 1804.

[43]

HAN W, LI X, CAI L, et al. Vacuum sintering of HUST-1 lunar regolith simulants with different particle sizes[J]. Construction and Building Materials, 2025, 490: 142618.

[44]

HOSSAIN S S, BULLARD J W. Fabrication of intricate lunar regolith monoliths via freeze casting[J]. Journal of the European Ceramic Society, 2025, 45(10): 117328.

[45]

XUE G, QIAO G. Lunar regolith simulant-based geopolymer products prepared by the cold-sintering process: evolution of pore water distribution, reaction products, microstructure and performance[J]. Construction and Building Materials, 2025, 477: 141355.

[46]

GUPTA N, DAWARA V, KUMAR A, et al. Liquid state sintering enhances consolidation in basalt-rich lunar regolith[J]. Advances in Space Research, 2024, 74(4): 1693-1705.

基金资助

国家自然科学基金项目(92475202)

AI Summary AI Mindmap
PDF (33135KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉