PDF (15624K)
摘要
井塔结构是矿井工业场地内重要的地面塔式工业建筑,是实现材料运输、人员升降和矿物提升的重要通道。针对地上建筑高于60 m 的高大型混凝土井塔的相关抗震、动力特性和设备激振力作用研究相对较少。本文通过YJK 软件对某铜矿项目主井塔进行三维建模,计算在现行抗震标准下该结构在6 度、7 度和8 度地震作用下的地震响应,分析高大井塔结构的抗震薄弱环节,利用有限元软件Midas/Gen 重点对提升层大厅振动特性进行分析,并进一步研究电动机大梁单激励结构振动规律。结果表明:由于高宽比偏大、楼板开洞率高和荷载分布不均匀等原因,高大型混凝土井塔结构抗震薄弱处突出,在设计过程中需特别注意控制层间剪力和层间位移角。在设计时由于考虑设备安装、检修、楼面堆载等多工况,提升层大厅楼板和主梁刚度较大,提升设备自振频率较低,仅为5.33 Hz,远小于该功能层的自振频率,电动机的自振频率为9.78 Hz,穿越提升大厅层第2 阶和第3 阶模态,由于激振力较小激起的振动最大应力为0.143 N · mm−2,最大变形值为0.011 6 mm,最大变形速度为1.015 mm · s−1,均不足以引起该支撑梁振动,因此只要保障提升层大厅楼板和主梁具有足够刚度,在该提升系统下不会引起提升大厅功能层振动。
Abstract
Well tower structure is an important ground tower industrial building in the mine industrial site, and it is an important channel to realize material transportation, personnel lifting and mineral lifting.Relatively few studies have been conducted on the seismic performance, dynamic characteristics, and the effects of equipment excitation forces of high-rise concrete shaft towers with a height exceeding 60 meters above ground.This paper employs YJK software to carry out 3D modeling by the existing main well tower of a copper mine project, computes the seismic response of the structure under the earthquake actions of 6 degree, 7 degree and 8 degree under the current seismic standard, and analyzes the seismic weakness of the tall well tower structure. By using the finite element software MIDAS/GEN, the vibration characteristics of the elevator hall are analyzed, and the vibration law of the single excitation structure of the motor beam is further investigated. The results indicate that the seismic weakness of tall and large concrete tower structures is prominent due to the high aspect ratio, high floor opening rate and uneven load distribution. Special attention should be paid to controlling the interstory shear and interstory displacement angle in the design process. In the design, considering the conditions such as equipment installation, maintenance, floor loading, etc., the floor and main beam stiffness of the lifting floor hall is large, and the natural vibration frequency of the lifting equipment is low, merely 5.33 Hz, which is far less than the natural vibration frequency of the functional floor. The natural vibration frequency of the motor is 9.78 Hz, which passes through the second and third modes of the lifting hall floor. Due to the small excitation force, the maximum vibration stress caused is 0.143 N · mm−2, the maximum deformation value is 0.011 6 mm, and the maximum deformation speed is 1.015 mm·s−1, which are not sufficient to cause the vibration of the support beam and thus are not enough to cause the vibration of the functional layer of the lifting hall. Therefore, ensuring that the floor slab and main beam of the lifting hall have sufficient rigidity will not cause vibration in the functional layer of the lifting hall under this lifting system.
关键词
Key words
[Author(id=1330550313786880499, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, orderNo=0, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=hankun@bgrimm.com, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1330550313862377973, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550313786880499, language=EN, stringName=Kun HAN, firstName=Kun, middleName=null, lastName=HAN, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=BGRIMM Technology Group, Beijing 100160, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550313908515319, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550313786880499, language=CN, stringName=韩昆, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=矿冶科技集团有限公司, 北京 100160, bio={"content":"韩昆,硕士,工程师,主要从事结构设计。E-mail: hankun@bgrimm.com
"}, bioImg=null, bioContent=韩昆,硕士,工程师,主要从事结构设计。E-mail: hankun@bgrimm.com
, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550313711383022, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, xref=null, ext=[AuthorCompanyExt(id=1330550313728160239, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=BGRIMM Technology Group, Beijing 100160, China), AuthorCompanyExt(id=1330550313740743153, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=矿冶科技集团有限公司, 北京 100160)])]), Author(id=1330550313954652666, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, orderNo=1, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=qianchenyang@bgrimm.com, emailSecond=null, emailThird=null, correspondingAuthor=1, authorType=1, ext={EN=AuthorExt(id=1330550314017567229, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550313954652666, language=EN, stringName=Chenyang QIAN, firstName=Chenyang, middleName=null, lastName=QIAN, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=BGRIMM Technology Group, Beijing 100160, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550314063704575, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550313954652666, language=CN, stringName=钱晨阳, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=矿冶科技集团有限公司, 北京 100160, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550313711383022, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, xref=null, ext=[AuthorCompanyExt(id=1330550313728160239, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=BGRIMM Technology Group, Beijing 100160, China), AuthorCompanyExt(id=1330550313740743153, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=矿冶科技集团有限公司, 北京 100160)])]), Author(id=1330550314109841922, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, orderNo=2, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1330550314172756485, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550314109841922, language=EN, stringName=Guojiang FENG, firstName=Guojiang, middleName=null, lastName=FENG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=BGRIMM Technology Group, Beijing 100160, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550314218893831, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, authorId=1330550314109841922, language=CN, stringName=冯国将, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=矿冶科技集团有限公司, 北京 100160, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550313711383022, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, xref=null, ext=[AuthorCompanyExt(id=1330550313728160239, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=BGRIMM Technology Group, Beijing 100160, China), AuthorCompanyExt(id=1330550313740743153, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550312864133586, companyId=1330550313711383022, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=矿冶科技集团有限公司, 北京 100160)])])]
韩昆,钱晨阳,冯国将.
高大型混凝土井塔结构抗震及振动特性分析[J].
矿冶, 2026, 35(1): 138-146 DOI:10.3969/j.issn.1005-7854.2026.01.018
| [1] |
刘兵. 井塔的钢结构体系选型和提升大梁振动分析[D]. 西安: 西安建筑科技大学, 2019.
|
| [2] |
LIU B. Steel structure system selection of well tower and vibration analysis of lifting girder[D]. Xi'an: Xi'an University of Architecture and Technology, 2019.
|
| [3] |
刘正宇, 李爱兵, 邹平, 等. 下告铁矿主井井塔基础稳定性研究与设计[J]. 有色金属(矿山部分), 2009, 61(1): 42-45.
|
| [4] |
LIU Z Y, LI A B, ZOU P, et al. Research and design of shaft tower foundation stability of main shaft in Xiaogao iron mine[J]. Nonferrous Metals (Mining Section), 2009, 61(1): 42-45.
|
| [5] |
刘彦东, 王志杰, 刘兵, 等. 钢结构提升井塔体系的探讨[J]. 煤炭工程, 2020, 52(4): 12-16.
|
| [6] |
LIU Y D, WANG Z J, LIU B, et al. Discussion on steel structure lifting tower system[J]. Coal Engineering, 2020, 52(4): 12-16.
|
| [7] |
刘显旺. 葫芦素煤矿主井井塔结构设计研究[J]. 煤炭工程, 2023, 55(3): 25-29.
|
| [8] |
LIU X W. Research on tower structure design of main shaft in Hulusu coal mine[J]. Coal Engineering, 2023, 55(3): 25-29.
|
| [9] |
刘彦东. 纳林河矿井副立井井塔设计[J]. 煤炭工程, 2015, 47(8): 19-21, 24.
|
| [10] |
LIU Y D. Tower design of auxiliary shaft in Nalinhe mine[J]. Coal Engineering, 2015, 47(8): 19-21, 24.
|
| [11] |
中华人民共和国住房和城乡建设部. 建筑抗震设计规范: GB/T 50011-2010[S]. 北京: 中国建筑工业出版社, 2024. Ministry of Housing and Urban-Rural Development of the People's Republic of China.
|
| [12] |
Code for seismic design of buildings: GB/T 50011-2010[S]. Beijing: China Architecture & Building Press, 2024.
|
| [13] |
王丹. 提升机动载荷作用下井塔振动分析与寿命预测[D]. 阜新: 辽宁工程技术大学, 2009.
|
| [14] |
WANG D. Vibration analysis and life prediction of well tower under lifting dynamic load[D]. Fuxin: Liaoning Technical University, 2009.
|
| [15] |
王丽, 苏荣华. 煤矿主提升系统井塔振动分析[J]. 煤矿机械, 2003(11): 58-60.
|
| [16] |
WANG L, SU R H. Vibration analysis of shaft tower in main hoisting system of coal mine[J]. Coal Mine Machinery, 2003(11): 58-60.
|
| [17] |
滕黎明, 江锦波, 彭旭东, 等. 基于Laplace变换的干气密封轴向自由振动与强迫振动解析研究[J]. 振动与冲击, 2022, 41(21): 148-160.
|
| [18] |
TENG L M, JIANG J B, PENG X D, et al. Analytical study of axial free vibration and forced vibration of dry gas seals based on Laplace transform[J]. Journal of Vibration and Shock, 2022, 41(21): 148-160.
|
| [19] |
冯琳琳. 八字形强迫振动方柱绕流机理研究[D]. 哈尔滨: 哈尔滨工业大学, 2021.
|
| [20] |
FENG L L. Study on the mechanism of flow around a square column with forced eight-figure vibration[D]. Harbin: Harbin Institute of Technology, 2021.
|
| [21] |
肖长江, 张振宇. 钢井塔提升大厅层振动特性分析[J]. 陕西煤炭, 2021, 40(4): 20-23, 27.
|
| [22] |
XIAO C J, ZHANG Z Y. Vibration characteristics analysis of lifting hall layer of steel shaft tower[J]. Shaanxi Coal, 2021, 40(4): 20-23, 27.
|
| [23] |
李凤翔. 矿井提升机的3 500 kW同步电动机传动变频装置及其主要环节调试[J]. 矿冶, 1996, 5(3): 81-87, 111.
|
| [24] |
LI F X. 3 500 kW synchronous motor drive frequency conversion device of mine hoist and its main link debugging[J]. Mining and Metallurgy, 1996, 5(3): 81-87, 111.
|
| [25] |
中华人民共和国住房和城乡建设部. 动力机器基础设计标准: GB/T 50040-2020[S]. 北京: 中国建筑工业出版社, 2021. Ministry of Housing and Urban-Rural Development of the People's Republic of China.
|
| [26] |
Standard for design of dynamic machine foundation: GB/T 50040-2020[S]. Beijing: China Architecture & Building Press, 2021.
|
| [27] |
中华人民共和国住房和城乡建设部. 建筑工程容许振动标准: GB/T 50868-2013[S]. 北京: 中国建筑工业出版社, 2013.
|
| [28] |
Ministry of Housing and Urban-Rural Development of the People's Republic of China. Standard for allowable vibration of building engineering: GB/T 50868-2013[S]. Beijing: China Architecture & Building Press, 2013.
|
基金资助
矿冶科技集团有限公司技术提升项目(0101-45-00093)