阶段空场嗣后充填法回采顺序优化与采场稳定性控制

秦忠虎 ,  秦秀山 ,  刘强 ,  李亚楠 ,  李逸豪

矿冶 ›› 2026, Vol. 35 ›› Issue (2) : 190 -203.

PDF (41186KB)
矿冶 ›› 2026, Vol. 35 ›› Issue (2) : 190 -203. DOI: 10.3969/j.issn.1005-7854.2026.02.004
矿山地质、开采与安全

阶段空场嗣后充填法回采顺序优化与采场稳定性控制

作者信息 +

Research on optimization of mining sequence and stability control in sublevel drilling-stage room and subsequent filling mining

Author information +
文章历史 +
PDF (42173K)

摘要

为解决因斑岩型矿体开采地压规律不清、影响区域模糊而制约矿井安全高效开采的难题,以山西紫金矿业斑岩金矿1-6#勘探线范围为工程背景,提出了方案一“盘区顺序接续”、方案二“盘区间隔接续”2 种单中段回采顺序方案,以及方案三“相邻盘区矿房对齐回采”、方案四“相邻盘区矿房错开回采”、方案五“相邻盘区矿房间隔回采”、方案六“盘区与矿房均间隔回采”4 种相邻中段回采顺序方案。通过建立三维数值模型,对阶段空场嗣后充填法6 种不同方案进行数值分析,结果表明:单中段回采工况下,方案一、二两者主要力学状态接近,其中方案一最大剪应力32.7 MPa,比方案二小0.1 MPa,最大变形8.11 cm 仅比方案二小0.05 cm,从塑性区的分布看,方案二的塑性区体积大且分散不均匀不易控制;相邻中段同步回采工况下,方案三指标较优,方案四、五力学响应强烈,方案六表现出最优稳定性,其最大剪应力为27.1 MPa,最大变形7.32 cm,塑性区体积35 397.03 m3,均为最低,且塑性区分布更分散。阶段空场嗣后充填法回采中,单中段宜采用相邻盘区依次接续顺序,相邻中段宜采用间隔盘区同步回采顺序,可有效控制采场稳定性。研究成果能够为同类矿山回采顺序优化及稳定性控制提供理论支撑与工程参考。

Abstract

To address the challenge of unclear geostatic pressure behavior and ambiguous influence zones in porphyry ore body mining, which restricts safe and efficient mining operations, this study focuses on the engineering context of the 1-6# exploration lines at Shanxi Zijin Mining's porphyry gold deposit. Two single-level mining sequence schemes are proposed: Scheme Ⅰ "Sequential Panel Succession" and Scheme Ⅱ "Alternate Panel Succession". Additionally, four adjacent-level mining sequence schemes are introduced: Scheme Ⅲ "Aligned Stope Mining in Adjacent Panels", Scheme Ⅳ "Staggered Stope Mining in Adjacent Panels", Scheme Ⅴ "Alternate Stope Mining in Adjacent Panels", and Scheme Ⅵ "Alternate Panel and Stope Mining". Through the establishment of a three-dimensional numerical model, a numerical analysis was conducted for these six different schemes of the open stoping with subsequent backfill method. The results showed that under the single stage mining condition, the main mechanical states of Scheme 1 and Scheme 2 were similar. Among them, Scheme 1 had a maximum shear stress of 32.7 MPa, which was 0.1 MPa lower than Scheme 2, and a maximum deformation of 8.11 cm, which was only 0.05 cm smaller than Scheme 2. From the distribution of plastic zones, Scheme 2 had similar plastic deformation. The large volume and uneven dispersion of the area are difficult to control; Under the synchronous mining conditions of adjacent stages, Scheme 3 has better indicators, Schemes 4 and 5 have strong mechanical responses, and Scheme 6 shows the best stability, with a maximum shear stress of 27.1 MPa, a maximum deformation of 7.32 cm, and the plastic zone volume of 35 397.03 m3 being the lowest, and the plastic zone distribution is more dispersed. In the sublevel drilling-stage room and subsequent filling method, adjacent panels should be sequentially connected in a single stage, and adjacent stages should be synchronously mined with interval panels, which can effectively control the stability of the mining area. The research results can provide theoretical support and engineering reference for optimizing the mining sequence and stability control of similar mines.

关键词

阶段空场嗣后充填法 / 回采顺序 / 数值模拟 / 方案优化 / 采场稳定性控制

Key words

sublevel drilling-stage room and subsequent filling method / mining sequence / numerical simulation / plan optimization / mining stability control

引用本文

引用格式 ▾
秦忠虎,秦秀山,刘强,李亚楠,李逸豪. 阶段空场嗣后充填法回采顺序优化与采场稳定性控制[J]. 矿冶, 2026, 35(2): 190-203 DOI:10.3969/j.issn.1005-7854.2026.02.004

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

王连成, 邵安林, 曲福明, 等. 金属矿山开采技术发展现状与展望[J]. 工程科学学报, 2025, 47(5): 971-983.

[2]

WANG L C, SHAO A L, QU F M, et al. Current status and outlook of metal mining technology development[J]. Journal of Engineering Science, 2025, 47(5): 971-983.

[3]

柳小波, 丛峰武, 张宝金, 等. 我国金属矿山智慧化转型实践与展望[J]. 金属矿山, 2025(5): 1-16.

[4]

LIU X B, CONG F W, ZHANG B J, et al. Practices and prospects of intelligent transformation in China's metal mines[J]. Metal Mine, 2025(5): 1-16.

[5]

许文远. 破碎矿体交错布置大跨度下向分段充填采矿技术研究[D]. 北京: 北京科技大学, 2024.

[6]

XU W Y. Research on large-span downward segmented filling mining technology for interlaced arrangement of broken ore bodies[D]. Beijing: University of Science and Technology Beijing, 2024.

[7]

王志君. 李楼铁矿空场嗣后充填法运行管理探讨[J]. 金属矿山, 2022(6): 35-39.

[8]

WANG Z J. Operational management of the subsequent backfilling method at the Lilou iron ore mine[J]. Metal Mine, 2022(6): 35-39.

[9]

田欣, 何荣兴, 张贤, 等. 石人沟铁矿采空区分段充填治理方案研究与应用[J]. 金属矿山, 2023(8): 162-170.

[10]

TIAN X, HE R X, ZHANG X, et al. Research and application of segmented backfilling management plan for the abandoned mine areas in Shirengou iron mine[J]. Metal Mine, 2023(8): 162-170.

[11]

陈霖, 黄明清, 唐绍辉, 等. 大直径深孔空场嗣后充填法采场结构参数优化及稳定性分析[J]. 金属矿山, 2022(11): 44-51.

[12]

CHEN L, HUANG M Q, TANG S H, et al. Optimization of structural parameters and stability analysis for large-diameter deep-hole open-stoping mine with subsequent backfilling method[J]. Metal Mine, 2022(11): 44-51.

[13]

王玉丁, 林卫星, 欧任泽, 等. 分段凿岩阶段空场嗣后充填采矿法采场跨度的优化[J]. 矿业研究与开发, 2024, 44(6): 19-25.

[14]

WANG Y D, LIN W X, OU R Z, et al. Optimization of mining span in segmented drilling-and-blasting stage with subsequent backfilling mining method[J]. Mining Research and Development, 2024, 44(6): 19-25.

[15]

张瑞明, 魏丁一, 杜翠凤, 等. 阶段空场嗣后充填采矿法采场跨度及回采顺序优化研究[J]. 矿业研究与开发, 2022, 42(3): 10-14.

[16]

ZHANG R M, WEI D Y, DU C F, et al. Optimization of mining span and cutting sequence in stage-by-stage subsequent filling mining method[J]. Mining Research and Development, 2022, 42(3): 10-14.

[17]

甘德清, 孟岐, 刘志义, 等. 缓倾斜极厚矿体高阶段采场开采顺序优化[J]. 矿冶工程, 2024, 44(5): 28-34.

[18]

GAN D Q, MENG Q, LIU Z Y, et al. Optimization of mining sequence for high-stage mining areas in gentle-dip, ultra-thick ore bodies[J]. Mining and Metallurgical Engineering, 2024, 44(5): 28-34.

[19]

龙翼, 陈绍民, 严鹏. 断层条件下低品位厚大矿体采矿方法优化研究[J]. 金属矿山, 2023(4): 27-32.

[20]

LONG Y, CHEN S M, YAN P. Research on optimizing mining methods for low-grade, thick ore bodies under fault conditions[J]. Metal Mine, 2023(4): 27-32.

[21]

黄敏, 王晓军, 邱纪香, 等. 倾斜中厚矿体阶段空场嗣后充填采矿工艺优化研究[J]. 矿业科学学报, 2024, 9(4): 483-492.

[22]

HUANG M, WANG X J, QIU J X, et al. Research on optimization of step-by-step backfilling mining process for inclined medium-to-thick ore bodies[J]. Journal of Mining Science, 2024, 9(4): 483-492.

[23]

商昱, 崔忠贵, 龚华平, 等. 基于采矿工艺重构与协同开采的小分段平底出矿小阶段空场法开发研究[J]. 矿产保护与利用, 2025, 45(4): 22-28.

[24]

SHANG Y, CUI Z G, GONG H P, et al. Research on small-segment flat-bottomed ore-discharge small-stage open-stop ing method based on mining process reconstruction and cooperative mining[J]. Conservation and Utilization of Mineral Resources, 2025, 45(4): 22-28.

[25]

张良兵, 毛德华, 李杰林, 等. 朱兰铁矿深部急倾斜厚大矿体回采顺序优化研究[J]. 矿业研究与开发, 2023, 43(3): 26-31.

[26]

ZHANG L B, MAO D H, LI J L, et al. Research on optimization of mining sequence for deep, steeply dipping, thick ore bodies in Zhulan iron mine[J]. Mining Research and Development, 2023, 43(3): 26-31.

[27]

熊朝辉, 谭玉叶, 楚立申, 等. 高阶段嗣后分层胶结充填体强度及结构优化研究[J]. 金属矿山, 2022(3): 35-42.

[28]

XIONG Z H, TAN Y Y, CHU L S, et al. Research on strength and structural optimization of high-stage post-stratified grout filling[J]. Metal Mine, 2022(3): 35-42.

[29]

余昕, 熊朝辉, 宋卫东, 等. 高阶段嗣后胶结充填法矿柱与充填体动态稳定性研究[J]. 矿业研究与开发, 2022, 42(4): 26-31.

[30]

YU X, XIONG Z H, SONG W D, et al. Study on dynamic stability of mine pillars and backfill in high-stage post-grouting backfilling method[J]. Mining Research and Development, 2022, 42(4): 26-31.

[31]

刘大可, 张浩强, 郭翔, 等. 帕鲁特金矿破碎矿体嗣后充填采矿法采场结构参数优化[J]. 矿业研究与开发, 2025, 45(1): 32-40.

[32]

LIU D K, ZHANG H Q, GUO X, et al. Optimization of mining area structural parameters for subsequent backfilling mining method in the Parutkin gold mine broken ore body[J]. Mining Research and Development, 2025, 45(1): 32-40.

[33]

黄德镛, 高聪, 贾子月, 等. 多中段空区稳定性分析及间柱回采顺序优选[J]. 有色金属工程, 2023, 13(6): 105-114.

[34]

HUANG D Y, GAO C, JIA Z Y, et al. Stability analysis of multi-level goaf and optimization of inter-pillar mining sequence[J]. Nonferrous Metals Engineering, 2023, 13(6): 105-114.

[35]

李冬萍, 张浩强. 金矿破碎矿体高分段嗣后充填采矿技术优化研究[J]. 金属矿山, 2021(12): 102-105.

[36]

LI D P, ZHANG H Q. Research on optimizing high-segmentation subsequent backfilling mining technology for crushed gold ore bodies[J]. Metal Mine, 2021(12): 102-105.

[37]

王社光, 向伟华, 赵兴东, 等. 高阶段充填采场顶板稳定性及支护参数优化研究[J]. 矿业研究与开发, 2025, 45(2): 33-41.

[38]

WANG S G, XIANG W H, ZHAO X D, et al. Research on roof stability and support parameter optimization in high-stage backfilled mining areas[J]. Mining Research and Development, 2025, 45(2): 33-41.

[39]

程爱平, 杜澳宇, 楚立申, 等. 考虑拱效应的高阶段充填体下采空区顶板跨度和厚度计算模型[J]. 采矿与安全工程学报, 2025, 42(1): 218-228.

[40]

CHENG A P, DU A Y, CHU L S, et al. Calculation model for span and thickness of roof in high-stage backfill areas considering arch effect[J]. Journal of Mining & Safety Engineering, 2025, 42(1): 218-228.

[41]

王谦源, 袁庆盟, 林敏, 等. 空场嗣后充填体稳定性分析与带式充填结构设计[J]. 矿业研究与开发, 2024, 44(6): 26-33.

[42]

WANG Q Y, YUAN Q M, LIN M, et al. Stability analysis of subsequent backfill in open pits and design of belt-type backfill structures[J]. Mining Research and Development, 2024, 44(6): 26-33.

基金资助

“十四五”国家重点研发计划项目(2022YFC2903804)

AI Summary AI Mindmap
PDF (41186KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉