PDF (5476K)
摘要
选矿厂矿仓尺寸参数通常根据所贮存矿石的堆积角进行经验设计,但在矿石含水率高、含泥量大时,易出现物料堆积板结、有效容积利用率低等问题,严重影响工艺流程的通畅性与矿山正常生产。针对上述问题,本文提出一种模拟仿真与优化设计相结合的矿仓设计方法。以钼矿中细碎仓物料、钼矿高压辊磨仓物料、铜矿粉矿仓物料、铝土矿原矿仓物料四种物料类型为研究对象,采用 Cradle 软件开展离散元模拟仿真试验,系统揭示了黏性阻尼系数、静摩擦系数及滚动阻力系数对颗粒堆积行为的影响规律,并建立了多种矿石颗粒流的参数化模型,组建相应数据库以提升陌生物料的建模效率。在阐明矿仓半顶角、卸料口尺寸及矿仓高度等关键参数对卸料性能影响规律的基础上,引入仓内颗粒占总容积70% 和30% 时料层表面与水平面的夹角、料拱高度、料拱维持时间及成拱瞬时应力等多维指标,构建矿仓卸料性能评价体系。结合Jenike 理论与临界拱高公式,分析了卸料口尺寸与料拱高度、颗粒黏结力与临界成拱高度之间的定量关系。以新疆某铜矿为例进行应用验证,通过模拟评估优化后的矿仓卸料效果,结果表明:矿仓半顶角过大易导致物料出现静止区、卸料流型转变为中心流;根据仿真结果增大卸料口尺寸后,棚料状况明显改善,模拟结果与现场实际工况吻合良好。研究验证了所提方法的可靠性与工程实用价值,为复杂工况下矿仓的精细化设计提供了理论依据与技术支撑。
Abstract
The dimensional parameters of ore bins in mineral processing plants are typically designed empirically based on the repose angle of the stored ore. However, when the ore has high moisture and clay content, issues such as material compaction and low effective volume utilization rate are prone to occur, severely impacting the smoothness of the process flow and normal mine production. To address these problems, this paper proposes an ore bin design method that integrates simulation and optimization design. Four types of materials were taken as research objects, including materials from the medium-fine crushing bin of molybdenum ore, materials from the high-pressure grinding roll bin of molybdenum ore, fine ore bin materials of copper ore, and run-of-mine bin materials of bauxite. Discrete element simulation tests were carried out using Cradle software to systematically reveal the influence laws of viscous damping coefficient, static friction coefficient and rolling resistance coefficient on particle accumulation behavior. Parametric models for particle flow of various ores were established, and a corresponding database was constructed to improve the modeling efficiency for unfamiliar materials. Based on elucidating the influence patterns of key parameters-such as bin half-angle, outlet size, and bin height-on discharge performance, a multi-dimensional evaluation system for ore bin discharge performance was constructed. This system incorporates indicators including the angle between the material layer surface and the horizontal plane when the internal particles account for 70% and 30% of the total volume, arch height, arch duration, and instantaneous arching stress. Combining Jenike's theory and the critical arching height formula, the quantitative relationships between outlet size and arch height, as well as between particle cohesion and critical arching height, were analyzed. A copper mine in Xinjiang was taken as a case study for application verification. The optimized ore bin discharge effect was evaluated through simulation. The results indicate that an excessively large bin half-angle can easily lead to stagnant zones in the material, transforming the discharge flow pattern into funnel flow. Increasing the outlet size based on simulation results significantly improved the bridging situation, with simulation findings showing good agreement with actual site conditions. This study validates the reliability and engineering practical value of the proposed method, providing a theoretical basis and technical support for the refined design of ore bins under complex operating conditions.
关键词
Key words
[Author(id=1330550377565213159, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, orderNo=0, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=18370979262@163.com, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1330550377619739113, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377565213159, language=EN, stringName=Jun WANG, firstName=Jun, middleName=null, lastName=WANG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=CINF Engineering Co. Ltd., Changsha 410019, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550377665876458, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377565213159, language=CN, stringName=王俊, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=长沙有色冶金设计研究院有限公司, 长沙 410019, bio={"content":"王俊,硕士,高级工程师,研究方向为矿山机械工程。E-mail: 18370979262@163.com
"}, bioImg=null, bioContent=王俊,硕士,高级工程师,研究方向为矿山机械工程。E-mail: 18370979262@163.com
, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550377498104289, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, xref=null, ext=[AuthorCompanyExt(id=1330550377510687202, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=CINF Engineering Co. Ltd., Changsha 410019, China), AuthorCompanyExt(id=1330550377523270115, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=长沙有色冶金设计研究院有限公司, 长沙 410019)])]), Author(id=1330550377707819500, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, orderNo=1, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=13689295605@163.com, emailSecond=null, emailThird=null, correspondingAuthor=1, authorType=1, ext={EN=AuthorExt(id=1330550377762345454, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377707819500, language=EN, stringName=Kai JIN, firstName=Kai, middleName=null, lastName=JIN, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=CINF Engineering Co. Ltd., Changsha 410019, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550377804288497, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377707819500, language=CN, stringName=金凯, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=长沙有色冶金设计研究院有限公司, 长沙 410019, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550377498104289, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, xref=null, ext=[AuthorCompanyExt(id=1330550377510687202, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=CINF Engineering Co. Ltd., Changsha 410019, China), AuthorCompanyExt(id=1330550377523270115, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=长沙有色冶金设计研究院有限公司, 长沙 410019)])]), Author(id=1330550377846231539, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, orderNo=2, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1330550377900757495, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377846231539, language=EN, stringName=Jinshan YANG, firstName=Jinshan, middleName=null, lastName=YANG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=CINF Engineering Co. Ltd., Changsha 410019, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550377942700537, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377846231539, language=CN, stringName=杨金山, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=长沙有色冶金设计研究院有限公司, 长沙 410019, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550377498104289, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, xref=null, ext=[AuthorCompanyExt(id=1330550377510687202, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=CINF Engineering Co. Ltd., Changsha 410019, China), AuthorCompanyExt(id=1330550377523270115, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=长沙有色冶金设计研究院有限公司, 长沙 410019)])]), Author(id=1330550377984643580, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, orderNo=3, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1330550378034975231, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377984643580, language=EN, stringName=Jiangang ZHANG, firstName=Jiangang, middleName=null, lastName=ZHANG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=CINF Engineering Co. Ltd., Changsha 410019, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1330550378076918271, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, authorId=1330550377984643580, language=CN, stringName=张建刚, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=null, address=长沙有色冶金设计研究院有限公司, 长沙 410019, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1330550377498104289, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, xref=null, ext=[AuthorCompanyExt(id=1330550377510687202, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=CINF Engineering Co. Ltd., Changsha 410019, China), AuthorCompanyExt(id=1330550377523270115, tenantId=1045748351789510663, journalId=1327662813561454606, articleId=1330550376457916891, companyId=1330550377498104289, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=长沙有色冶金设计研究院有限公司, 长沙 410019)])])]
王俊,金凯,杨金山,张建刚.
基于离散元仿真模拟的颗粒流建模与矿仓参数优化[J].
矿冶, 2026, 35(2): 250-258 DOI:10.3969/j.issn.1005-7854.2026.02.010
| [1] |
蔡同祥, 王学文, 王淑平, 等. 筒仓卸料时超压与变形分析[J]. 中国粉体技术, 2015, 21(4): 15-19.
|
| [2] |
CAI T X, WANG X W, WANG S P, et al. Analysis on lateral overpressure and deformation simulation during discharging in silo[J]. China Powder Science and Technology, 2015, 21(4): 15-19.
|
| [3] |
吴震, 王利强, 徐立敏, 等. 粉体料仓设计及卸料特性综述[J]. 中国粉体技术, 2023, 29(1): 19-30.
|
| [4] |
WU Z, WANG L Q, XU L M, et al. Powder silo design and discharge characteristics: a review[J]. China Powder Science and Technology, 2023, 29(1): 19-30.
|
| [5] |
欧阳鸿武, 黄誓成, 彭政, 等. 颗粒物质的堵塞行为[J]. 粉末冶金材料科学与工程, 2008(5): 260-268.
|
| [6] |
OUYANG H W, HUANG S C, PENG Z, et al. Jamming of granular matter[J]. Materials Science and Engineering of Powder Metallurgy, 2008(5): 260-268.
|
| [8] |
QIN Y, TIAN Y K, 等. 基于EDEM的煤仓卸料时煤散料流动特性分析[J]. 煤炭科学技术, 2015, 43(5): 130-134. WANG X W, QIN Y, TIAN Y K, et al. Analysis on flow features of bulk coal during coal unloading period based on EDEM[J]. Coal Science and Technology, 2015, 43(5): 130-134.
|
| [9] |
杜建斌, 任世业. 基于DEM-MBD-FEM的振动筛物料冲击性能研究[J]. 现代矿业, 2024, 40(12): 219-222, 226.
|
| [10] |
DU J B, REN S Y. Research on material impact properties of vibrating screen based on DEM-MBD-FEM[J]. Modern Mining, 2024, 40(12): 219-222, 226.
|
| [11] |
韦熙, 周甲伟, 徐耀杰. 基于DEM模拟的筒仓卸料过程瞬时拱影响因素分析[J]. 包装与食品机械, 2024, 42(4): 56-66.
|
| [12] |
WEI X, ZHOU J W, XU Y J. Analysis of influence factors of instantaneous arch during silo discharging process based on DEM simulation[J]. Packaging and Food Machinery, 2024, 42(4): 56-66.
|
| [13] |
郭慧珠. 筒仓中物料流动特性研究[D]. 太原: 太原科技大学, 2014.
|
| [14] |
GUO H Z. Study on flow characteristics of materials in silos[D]. Taiyuan: Taiyuan University of Science and Technology, 2014.
|
| [15] |
杨世明, 刘克瑾, 姚辉江, 等. 粒径对平底筒仓中心卸料的流态及仓壁压力分布的影响[J]. 中国油脂, 2025, 50(7): 145-152.
|
| [16] |
YANG S M, LIU K J, YAO H J, et al. Influence of particle size on flow pattern and wall pressure distribution of central discharge in flat-bottom silo[J]. China Oils and Fats, 2025, 50(7): 145-152.
|
| [17] |
陈泉. 矿仓内颗粒流动力学特征的多尺度测量和研究[D]. 上海: 上海理工大学, 2021.
|
| [18] |
CHEN Q. Multiscale measurement and investigation on dynamic characteristics of particle flow in ore bins[D]. Shanghai: University of Shanghai for Science and Technology, 2021.
|
| [19] |
刘克瑾, 黄硕硕, 姚辉江, 等. 贮料重度对卸料流态及仓壁压力分布的影响[J]. 农业工程学报, 2024, 40(15): 44-53.
|
| [20] |
LIU K J, HUANG S S, YAO H J, et al. Influences of gravity density on discharge flow pattern and pressure distribution along silo walls[J]. Transactions of the Chinese Society of Agricultural Engineering, 2024, 40(15): 44-53.
|
| [21] |
GUTIÉRREZ G D, MONCADA D Z, ZÚÑIGA I, et al. Influence of particle size in silo discharge[J]. The European Physical Journal Conferences, 2017, 140: 03021.
|
| [22] |
XU C, WANG F L, WANG L P, et al. Inter-orifice distance dependence of flow rate in a quasi-two-dimensional hopper with dual outlets[J]. Powder Technology, 2018, 328: 7-12.
|
| [23] |
叶方平, 李郁, 胡吉全, 等. 颗粒凝聚力对筒仓装卸过程影响的研究[J]. 武汉理工大学学报, 2016, 38(7): 91-96.
|
| [24] |
YE F P, LI Y, HU J Q, et al. Research of particle cohesion influence on the silo loading and unloading process[J]. Journal of Wuhan University of Technology, 2016, 38(7): 91-96.
|
| [25] |
刘克瑾, 姚辉江, 袁铮. 平底筒仓中心卸料流态演化过程及仓壁压力波动性[J]. 农业工程学报, 2023, 39(15): 15-24.
|
| [26] |
LIU K J, YAO H J, YUAN Z. Evolution process of center discharge flow pattern and pressure fluctuation of silo wall in a flat-bottomed silo[J]. Transactions of the Chinese Society of Agricultural Engineering, 2023, 39(15): 15-24.
|
| [27] |
谭援强, 郑军辉, 张浩, 等. 基于离散元法的锥形筒仓中颗粒流体的数学模拟[J]. 过程工程学报, 2015, 15(6): 916-922.
|
| [28] |
TAN Y Q, ZHENG J H, ZHANG H, et al. Mathematical simulation of granular flow in conical silo based on discrete element method[J]. The Chinese Journal of Process Engineering, 2015, 15(6): 916-922.
|