基于连续底切与并联控制的异形断面TBM关键技术研究

李建斌 ,  杨小聪 ,  曹宸旭 ,  黄丹 ,  郑志杰 ,  李鹏宇

有色金属(矿山部分) ›› 2026, Vol. 78 ›› Issue (6) : 97 -110.

PDF (5226KB)
有色金属(矿山部分) ›› 2026, Vol. 78 ›› Issue (6) : 97 -110. DOI: 10.20238/j.issn.1671-4172.2026.06.010
TBM专刊

基于连续底切与并联控制的异形断面TBM关键技术研究

作者信息 +

Research on key technologies of non-circular-section TBM based on continuous undercutting and parallel control

Author information +
文章历史 +
PDF (5350K)

摘要

全断面隧道掘进机(Tunnel Boring Machine,TBM)在硬岩隧道施工中优势显著,但其圆形断面难以满足深部地下工程对空间利用率日益增长的需求。针对传统TBM 固定轴线掘进模式与异形断面成形之间的固有矛盾,本文提出一种基于连续底切与并联控制的异形断面TBM 新型构型。核心思想在于:通过连续底切刀具主动构造两个临空面,将破岩机制由传统的压剪主导转变为拉剪主导,从而大幅降低对轴向推进力的依赖;在此基础上,引入六自由度并联机构作为刀盘空间运动载体,实现刀盘位姿的精确调控。文章分析了连续底切临空面诱导破岩机理,建立了刀盘-并联耦合动力学模型,并提出了基于边界轨迹偏置的异形断面成形与路径规划方法。数值仿真与等比例实验平台验证结果表明:连续底切条件下边缘滚刀垂直力为中心滚刀的1.67倍,临空面诱导的裂纹呈现明显的连续扩展特征;并联机构各支链可在低冲击载荷下稳定跟踪预设轨迹;实验获得的岩渣粗糙度指数为508,片状剥离特征显著,断面成形轮廓与目标轨迹吻合良好。研究表明,连续底切-并联耦合构型可有效突破固定轴线约束,为异形断面硬岩隧道的机械化一次成型提供可行技术路径,适用于金属矿、煤矿巷道开挖。

Abstract

Full-face tunnel boring machines (TBMs) have clear advantages in hard-rock tunnelling,but their circular excavation profile cannot fully meet the increasing demand for higher space utilization in deep underground engineering. To address the inherent conflict between the fixed-axis excavation mode of conventional TBMs and the formation of non-circular sections,this paper proposes a novel non-circular-section TBM configuration based on continuous undercutting and parallel control. The proposed concept actively creates two free surfaces using continuous undercutting tools,transforming the rock-breaking mechanism from conventional compression-shear failure to tensile-shear-dominated failure and thereby reducing the dependence on axial thrust. A six-degree-of-freedom parallel mechanism is introduced as the spatial motion carrier of the cutterhead to enable accurate pose control. The free-surface-induced rock-breaking mechanism of continuous undercutting is analysed,a cutterhead-parallel coupled dynamic model is established,and a boundary-offset-based path planning method for non-circular section formation is proposed. Numerical simulations and scaled platform tests show that,under continuous undercutting conditions,the vertical force on the edge cutter is 1.67 times that on the central cutter,and the free surface induces clear continuous crack propagation. The parallel mechanism tracks the preset trajectory stably under low-impact loads. The experimentally obtained muck has a roughness index of 508 and shows pronounced flake-like spalling,while the formed section profile agrees well with the target trajectory. The results indicate that the continuous-undercutting and parallel-coupled configuration can effectively overcome the constraint of a fixed excavation axis and provides a feasible technical route for one-pass mechanized formation of non-circular hard-rock tunnels,with potential application in metal mine and coal mine roadway excavation.

关键词

异形断面TBM / 连续底切 / 并联控制 / 临空面破岩

Key words

non-circular-section TBM / continuous undercutting / parallel control / free-surface rock breaking

引用本文

引用格式 ▾
李建斌,杨小聪,曹宸旭,黄丹,郑志杰,李鹏宇. 基于连续底切与并联控制的异形断面TBM关键技术研究[J]. 有色金属(矿山部分), 2026, 78(6): 97-110 DOI:10.20238/j.issn.1671-4172.2026.06.010

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

李建斌. 中国隧道掘进机技术进展与展望[J]. 现代隧道技术,2024,61(2):178-189.

[2]

Li Jianbin. Advances and prospects of tunnel boring machine technology in China[J]. Modern Tunnelling Technology,2024,61(2):178-189.

[3]

刘泉声,潘玉丛,余宏淦,等. 深部金属矿山巷道TBM 掘进技术应用现状及研究进展[J]. 有色金属(矿山部分),2024,76(6):25-41.

[4]

Liu Quansheng,Pan Yucong,Yu Honggan,et al. Application status and research progress of TBM tunnelling technology in deep metal mine roadways[J]. Nonferrous Metals (Mining Section),2024,76(6):25-41.

[5]

洪开荣,王杜娟,郭如军. 我国硬岩掘进机的创新与实践[J]. 隧道建设(中英文),2018,38(4):519-532.

[6]

Hong Kairong,Wang Dujuan,Guo Rujun. Innovation and practice of hard rock TBM in China[J]. Tunnel Construction,2018,38(4):519-532.

[7]

崔胤,贺飞,齐志冲,等. TBM 滚刀布置方案对比分析与评价[J]. 隧道建设(中英文),2018,38(3):474-480.

[8]

Cui Yin,He Fei,Qi Zhichong,et al. Comparative analysis and evaluation of different disc cutter layout schemes for TBM[J]. Tunnel Construction,2018,38(3):474-480.

[9]

许丙南,赵新合,陈良武,等. “全—半断面”工况下TBM贯入度影响因素分析[J]. 中国安全科学学报,2023,33(增刊2):202-208.

[10]

Xu Bingnan,Zhao Xinhe,Chen Liangwu,et al. Analysis of influencing factors of TBM penetration under "full and half sections"[J]. China Safety Science Journal,2023,33(S2):202-208.

[11]

宁向可,耿麒,卢智勇,等. 全断面隧道掘进机锥面刀盘滚刀破岩机制研究[J]. 现代隧道技术,2023,60(2):73-83.

[12]

Ning Xiangke,Geng Qi,Lu Zhiyong,et al. A study on the rock—breaking mechanism of disc cutters on cone cutterhead of full—face tunnel boring machines[J]. Modern Tunnelling Technology,2023,60(2):73-83.

[13]

张照煌,纪玮,翁子才. 锥面刀盘盾构主参数确定理论及模拟分析[J]. 机械工程学报,2021,57(11):243-255.

[14]

Zhang Zhaohuang,Ji Wei,Weng Zicai. Determination theory of main parameters and simulation analysis of the conical cutterhead shield[J]. Journal of Mechanical Engineering,2021,57(11):243-255.

[15]

赵振威,郑康泰,李楠,等. 不同几何结构的TBM 刀盘静力学性能对比分析[J]. 隧道建设,2016,36(1):102-107.

[16]

Zhao Zhenwei,Zheng Kangtai,Li Nan,et al. Analysis on static mechanical performances of TBM cutterhead with different geometries[J]. Tunnel Construction,2016,36(1):102-107.

[17]

耿麒,赵振平,陈建勋,等. 临空面辅助的TBM 滚刀群掘进试验与数值模拟[J]. 浙江大学学报(工学版),2025,59(4):759-768.

[18]

Geng Qi,Zhao Zhenping,Chen Jianxun,et al. Experimental and numerical study on excavation process induced by TBM disc cutter group assisted by different free faces[J]. Journal of Zhejiang University (Engineering Science),2025,59(4):759-768.

[19]

耿麒,魏正英,孟昊,等. TBM 的平面刀盘与两级刀盘的力学性能对比分析[J]. 西安交通大学学报,2015,49(3):121-128.

[20]

Geng Qi,Wei Zhengying,Meng Hao,et al. Comparison of mechanical performances between the two—stage cutterhead and the flat—face cutterhead for rock tunnel boring machine[J]. Journal of Xi'an Jiaotong University,2015,49(3):121-128.

[21]

Geng Qi,Wei Zhengying,Meng Hao,et al. Free—face—assisted rock breaking method based on the multi—stage tunnel boring machine (TBM) cutterhead[J]. Rock Mechanics and Rock Engineering,2016,49(11):4459-4472.

[22]

徐福通,卢景景,周辉,等. 预切槽和TBM 机械滚刀的新型联合破岩模式研究[J]. 岩土力学,2021,42(5):1363-1372.

[23]

Xu Futong,Lu Jingjing,Zhou Hui,et al. Research on combined rock—breaking mode of pre—cutting groove and TBM mechanical cutter[J]. Rock and Soil Mechanics,2021,42(5):1363-1372.

[24]

夏毅敏,张旭辉,谭青,等. 预切槽刀具切削岩土介质特性研究[J]. 现代隧道技术,2017,54(6):166-173.

[25]

Xia Yimin,Zhang Xuhui,Tan Qing,et al. Study on properties of cutting rock and soil medium by pre—cutting cutters[J]. Modern Tunnelling Technology,2017,54(6):166-173.

[26]

吴深,韩书晴,肖艳秋,等. TBM 盘形滚刀破岩过程的数值模拟综述[J]. 科学技术与工程,2025,25(28):11877-11887.

[27]

Wu Shen,Han Shuqing,Xiao Yanqiu,et al. Review of numerical simulation of rock—breaking process by TBM disc cutter[J]. Science Technology and Engineering,2025,25(28):11877-11887.

[28]

孙浩凯,高阳,朱光轩,等. 隧道掘进机滚刀破岩动态荷载理论模型及试验研究[J]. 岩土力学,2023,44(6):1657-1670.

[29]

Sun Haokai,Gao Yang,Zhu Guangxuan,et al. Theoretical and experimental study of tunnel boring machine dynamic cutting force[J]. Rock and Soil Mechanics,2023,44(6):1657-1670.

[30]

王帅,刘鹏远,李阁强,等. 全断面竖井掘进机锥形刀盘破岩机理研究[J]. 兵器装备工程学报,2024,45(4):287—293,300.

[31]

Wang Shuai,Liu Pengyuan,Li Geqiang,et al. Research on rock breaking mechanism for conical cutterhead of full—face shaft boring machine[J]. Journal of Ordnance Equipment Engineering,2024,45(4):287—293,300.

[32]

朱英,李建斌,曹宸旭,等. 悬臂TBM 新型刀盘设计[J]. 隧道建设(中英文),2025,45(增刊2):365-370.

[33]

Zhu Ying,Li Jianbin,Cao Chenxu,et al. Novel cutterhead design for cantilever TBMs[J]. Tunnel Construction,2025,45(S2):365-370.

[34]

徐光亿,齐志冲,赵子辉,等. 基于扩孔竖井掘进机开挖工法的锥形刀盘设计与试验[J]. 隧道建设(中英文),2026,46(1):194-203.

[35]

Xu Guangyi,Qi Zhichong,Zhao Zihui,et al. Design and testing of a cone—shaped cutterhead based on boring method for enlarged—diameter vertical shafts[J]. Tunnel Construction,2026,46(1):194-203.

[36]

苏翠侠. 大直径竖井掘进机锥面刀盘破岩仿真研究[J]. 地下空间与工程学报,2023,19(6):2020-2027.

[37]

Su Cuixia. Rock breaking simulation study of conical cutterhead for large—diameter vertical shaft boring machine[J]. Chinese Journal of Underground Space and Engineering,2023,19(6):2020-2027.

[38]

叶鹏达,尤晶晶,仇鑫,等. 并联机器人运动性能的研究现状及发展趋势[J]. 南京航空航天大学学报,2020,52(3):363-377.

[39]

Ye Pengda,You Jingjing,Qiu Xin,et al. Status and development trend of motion performance in parallel robot[J]. Journal of Nanjing University of Aeronautics & Astronautics,2020,52(3):363-377.

[40]

Huang Tian,Wang Jinsong,Whitehouse DJ. Closed form solution to the local dexterity and isotropy of Stewart parallel manipulators[J]. Journal of Mechanical Engineering,1999(5):41-46.

[41]

Chen Li. Wholly dynamic modeling of 6—DOF Stewart platform parallel robot[J]. Journal of Yanshan University,2004(3):228-232.

[42]

张世雄,黄丹,郑志杰,等. 某金矿悬臂式掘进机机械采掘试验研究[J]. 有色金属(矿山部分),2024,76(6):84—90.

[43]

Zhang Shixiong,Huang Dan,Zheng Zhijie,et al. Experimental study on mechanical mining with cantilever roadheader in a gold mine[J]. Nonferrous Metals (Mining Section),2024,76(6):84-90.

[44]

张超,张旭辉,杨文娟,等. 煤矿井下非全断面掘进移机路径规划方法研究[J]. 煤炭学报,2025,50(增刊2):1202-1214.

[45]

Zhang Chao,Zhang Xuhui,Yang Wenjuan,et al. Research on the planning method of non—full section tunneling path of boom—type roadheader in underground coal mine[J]. Journal of China Coal Society,2025,50(S2):1202-1214.

[46]

王苏彧,田劼,吴淼. 纵轴式掘进机截割轨迹规划及边界控制方法研究[J]. 煤炭科学技术,2016,44(4):89—94,118.

[47]

Wang Suyu,Tian Jie,Wu Miao. Study on cutting trace planning of longitudinal roadheader and boundary control method[J]. Coal Science and Technology,2016,44(4):89—94,118.

[48]

Li Weijia. Study on the condition number of Jacobian matrix of Stewart platforms[J]. Journal of Huazhong University of Science and Technology,1997,25(11):33-35.

[49]

夏毅敏,吴元,郭金成,等. TBM 边缘滚刀破岩机理的数值研究[J]. 煤炭学报,2014,39(1):172-178.

[50]

Xia Yimin,Wu Yuan,Guo Jincheng,et al. Numerical simulation of rock—breaking mechanism by gage disc cutter of TBM[J]. Journal of China Coal Society,2014,39(1):172-178.

[51]

李忠艳,刘杨,张雯超,等. TBM 常截面盘形滚刀破岩过程受力研究[J]. 人民长江,2025,56(1):173—179,204.

[52]

Li Zhongyan,Liu Yang,Zhang Wenchao,et al. Research on force of disc cutter during TBM rock breaking process[J]. Yangtze River,2025,56(1):173—179,204.

[53]

Ye Yang,Gao Shuai,Guan Xingyin,et al. Analysis on maximum force on connecting rod of low—speed Stewart platform[J]. Journal of Machine Design,2025,42(5):166-174.

[54]

徐颖,冯凤凤,程琳,等. 基于岩渣粒径分布规律的SBM 破岩效率研究[J]. 安徽理工大学学报(自然科学版),2025,45(3):58-65.

[55]

Xu Ying,Feng Fengfeng,Cheng Lin,et al. Study on rock breaking efficiency of SBM based on rock slag particle size distribution[J]. Journal of Anhui University of Science and Technology (Natural Science),2025,45(3):58-65.

[56]

闫长斌,樊明辉,陈馈,等. 基于岩渣粒径分布规律的TBM 刀具消耗分析[J]. 煤炭学报,2020,45(12):4216-4227.

[57]

Yan Changbin,Fan Minghui,Chen Kui,et al. Analysis on TBM cutter consumption based on the particle size distribution of rock debris[J]. Journal of China Coal Society,2020,45(12):4216-4227.

基金资助

新疆自治区重点研发计划(2024B03014-2)

AI Summary AI Mindmap
PDF (5226KB)

5

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉