TBM 始发硐室群围岩稳定性及开挖工法优化研究
周少兵 , 刘荣乐 , 李明睿 , 孙志浩 , 张春虎 , 周新勍
有色金属(矿山部分) ›› 2026, Vol. 78 ›› Issue (6) : 145 -154.
TBM 始发硐室群围岩稳定性及开挖工法优化研究
Stability of surrounding rock and optimization of excavation methods for TBM launching chamber groups
针对矿山TBM 大型始发硐室群开挖的围岩稳定性问题,本文以江西某金属矿山为背景,利用PLAXIS 3D数值模拟,研究了斜坡道分层法与小断面扩刷法两类施工工艺下大断面组装硐室围岩变形和应力分布特征。研究表明:斜坡道分层法对应的围岩变形量峰值为3. 20 mm,小于小断面扩刷法(峰值3. 30~3. 41 mm);两类工法在施工过程中均会在拐角处出现应力集中,且在施工完成后出现残余应力,其中,斜坡道分层法施工产生的最大残余应力为49. 7 MPa,小断面扩刷法施工产生的最大残余应力为16. 7 MPa,综合考虑变形控制效果与施工机械化程度,推荐优先采用斜坡道分层法,并实施“锚杆+ 钢筋网”临时支护。研究成果可为深部金属矿山TBM 始发硐室群的设计与施工提供科学依据。
To address the stability issues of surrounding rock during the excavation of large-scale TBM launching chamber groups in deep mines,this study takes a TBM launching chamber group project in a metal mine in Jiangxi Province as the engineering background. Using PLAXIS 3D numerical simulation software,the deformation and stress distribution characteristics of the surrounding rock of a large-section assembly chamber were investigated under two construction methods:the ramp bench method and the small-section pilot tunnel enlargement method. The results indicate that the peak surrounding rock deformation induced by the ramp bench method is 3. 20 mm,which is smaller than that of the small-section enlargement method (peak values ranging from 3. 30 to 3. 41 mm). Both methods exhibit stress concentration at corners during construction and residual stress after completion. The maximum residual stress generated by the ramp bench method is 49. 7 MPa,while that of the small-section pilot tunnel enlargement method is 16. 7 MPa. Considering the overall deformation control effect and the degree of mechanization,the ramp bench method is recommended as the preferred approach,with immediate support using “rock bolts+steel mesh” applied at corner locations. The research findings can provide a scientific basis for the design and construction of TBM launching chamber groups in deep metal mines.
| [1] |
陈发兴,蔡光辉,胡韬. 浅谈TBM 在金属矿山的应用[J]. 有色金属设计,2021,48(2):1-8. |
| [2] |
|
| [3] |
刘荣乐,樊忠华,张春虎, |
| [4] |
|
| [5] |
刘荣乐,张春虎,周新勍, |
| [6] |
|
| [7] |
黄建鑫. TBM 在某金属矿山长距离井巷掘进中的应用[J]. 现代矿业,2023,39(7):205-209. |
| [8] |
|
| [9] |
侯朝炯. 深部巷道围岩控制的关键技术研究[J]. 中国矿业大学学报,2017,46(5):970-978. |
| [10] |
|
| [11] |
张俊文. 深部大规模松软围岩巷道破坏分区理论分析[J]. 中国矿业大学学报,2017,46(2):292-299. |
| [12] |
|
| [13] |
陈顺满,吴爱祥,王少勇, |
| [14] |
|
| [15] |
王琦,王雷,刘博宏, |
| [16] |
|
| [17] |
杨仁树,朱晔,李永亮, |
| [18] |
|
| [19] |
侯朝炯. 深部巷道围岩控制的有效途径[J]. 中国矿业大学学报,2017,46(3):467-473. |
| [20] |
|
| [21] |
刘永乐. 深部高应力硐室群开挖与支护技术研究[D]. 青岛:山东科技大学,2019. |
| [22] |
|
| [23] |
杨仁树,薛华俊,郭东明, |
| [24] |
|
| [25] |
陈佳琪. 超大跨软弱富水破碎岩层硐室群施工方法优化研究[J]. 铁道建筑技术,2025(3):150-153. |
| [26] |
|
| [27] |
王炯,王浩,郭志飚, |
| [28] |
|
| [29] |
王炯,马磊,刘鹏, |
| [30] |
|
| [31] |
董亚宁,金爱兵,陈成, |
| [32] |
|
| [33] |
尹升华,寇永渊,周昀, |
| [34] |
|
| [35] |
李玉选,郭红斌,黄丹, |
| [36] |
|
| [37] |
关宝树. 隧道工程设计要点集[M]. 北京:人民交通出版社,2003. |
| [38] |
|
| [39] |
刘志祥,张海清. PLAXIS 高级应用教程[M]. 北京:机械工业出版社,2015. |
| [40] |
|
| [41] |
黄玉兵,王琦,高红科, |
| [42] |
|
/
| 〈 |
|
〉 |