PDF (48520K)
摘要
采用电阻焊、激光焊和熔化极惰性气体保护焊 (MIG) 3 种工艺对轧制复合板进行搭接焊接试验,综合运用金相显微镜、扫描电镜和电子背散射衍射等手段,分析焊缝宏观形貌、微观组织、元素分布、晶粒尺寸及晶界特征,并结合显微硬度、纳米压痕、拉伸断口及 180°弯曲试验评价接头力学性能,探究焊接方式对 304/201/304 不锈钢复合板搭接接头性能的影响。结果表明:3 种方法均可获得无宏观缺陷的接头,但在焊缝形貌、组织及性能上差异显著。电阻焊和激光焊热输入较低、冷却快,焊缝中心为细小等轴树枝晶,平均晶粒尺寸分别为 10.6 μm 和 10.1 μm,焊缝边缘为细小柱状晶;MIG 焊热输入高、冷却慢,焊缝中心为粗大柱状树枝晶,平均晶粒尺寸达 27.6 μm。元素分布上,电阻焊接头为自熔化焊接,Mn 含量最高;激光焊因添加低 Mn 焊丝,Mn 含量最低;MIG 接头介于两者之间。力学性能上,电阻焊接头硬度最高 (焊缝区域平均为 258.8 HV,焊缝中心纳米硬度为 5.15 GPa),归因于细晶强化、高位错密度及 Mn 固溶强化的协同作用,但塑性最差;激光焊接头硬度次之 (255.7 HV,纳米硬度 5.11 GPa),强度与塑性匹配最佳;MIG 接头硬度最低 (244.1 HV,纳米硬度 5.01 GPa),塑性最优。3 种接头均能通过 180°弯曲试验,抗弯性能良好。本研究为汽车燃油系统用不锈钢复合板焊接方法的工程选用提供了依据。
Abstract
To investigate the effect of welding methods on the lap joint performance of 304/201/304 stainless steel composite plates, three welding methods, namely resistance welding, laser welding, and metal inert gas (MIG) welding, were applied to lap-weld the rolled composite plates. The macroscopic weld morphology, microstructure, elemental distribution, grain size, and grain boundary characteristics were analyzed by means of optical microscopy, scanning electron microscopy, and electron backscatter diffraction, and the mechanical properties were evaluated by microhardness testing, nanoindentation, tensile fractography, and 180° bending tests. The results show that all three welding methods produce joints without macroscopic defects, but the weld morphology, joint microstructure, and properties differ. Resistance welding and laser welding have low heat input and fast cooling, resulting in fine equiaxed dendrites in the weld center with average grain sizes of 10.6 μm and 10.1 μm, respectively, and fine columnar grains at the weld edge. MIG welding has high heat input and slow cooling, resulting in coarse columnar dendrites in the weld center with an average grain size of 27.6 μm. In terms of elemental distribution, resistance welding exhibits the highest Mn content due to self-melting of the base metal, laser welding shows the lowest Mn content due to the addition of a low-Mn filler wire, and MIG falls between the two. Regarding mechanical properties, the resistance welded joint has the highest hardness, with an average microhardness of 258.8 HV in the weld zone and a nanohardness of 5.15 GPa at the weld center, which is mainly attributed to fine-grain strengthening, high dislocation density, and Mn solid-solution strengthening, but its plasticity is the poorest. The laser welded joint ranks second, with average values of 255.7 HV and 5.11 GPa, achieving the best balance between strength and plasticity. The MIG joint has the lowest hardness (244.1 HV and 5.01 GPa) but exhibits the best plasticity. Bending tests show that all three joints can withstand 180° bending and have good bending resistance. This study provides a basis for selecting welding methods for stainless steel composite plates used in automotive fuel systems.
关键词
Key words
[Author(id=1329514633930019292, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, orderNo=0, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1329514633988739550, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514633930019292, language=EN, stringName=Tonggang LIU, firstName=Tonggang, middleName=null, lastName=LIU, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1329514634034876895, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514633930019292, language=CN, stringName=刘同纲, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032, bio={"content":"刘同纲 (1997—),男,安徽宣城人,硕士生,主要研究方向为钢铁材料。
"}, bioImg=null, bioContent=刘同纲 (1997—),男,安徽宣城人,硕士生,主要研究方向为钢铁材料。
, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1329514633779024341, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, xref=1, ext=[AuthorCompanyExt(id=1329514633795801558, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China), AuthorCompanyExt(id=1329514633808384471, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032)])]), Author(id=1329514634081014241, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, orderNo=1, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=0, authorType=1, ext={EN=AuthorExt(id=1329514634139734499, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634081014241, language=EN, stringName=Chengsi ZHENG, firstName=Chengsi, middleName=null, lastName=ZHENG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1329514634194260452, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634081014241, language=CN, stringName=郑成思, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1329514633779024341, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, xref=1, ext=[AuthorCompanyExt(id=1329514633795801558, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China), AuthorCompanyExt(id=1329514633808384471, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032)])]), Author(id=1329514634240397798, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, orderNo=2, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=1, authorType=1, ext={EN=AuthorExt(id=1329514634307506664, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634240397798, language=EN, stringName=Mingya ZHANG, firstName=Mingya, middleName=null, lastName=ZHANG, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1329514634362032617, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634240397798, language=CN, stringName=张明亚, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=1, address=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1329514633779024341, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, xref=1, ext=[AuthorCompanyExt(id=1329514633795801558, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 School of Materials Science & Engineering, Anhui University of Technology , Maanshan 243032, China), AuthorCompanyExt(id=1329514633808384471, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633779024341, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=1 安徽工业大学 材料科学与工程学院 , 安徽 马鞍山 243032)])]), Author(id=1329514634408169963, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, orderNo=3, firstName=null, middleName=null, lastName=null, nameCn=null, orcid=null, stid=null, country=null, authorPic=null, dead=0, email=null, emailSecond=null, emailThird=null, correspondingAuthor=1, authorType=1, ext={EN=AuthorExt(id=1329514634471084525, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634408169963, language=EN, stringName=Feng LI, firstName=Feng, middleName=null, lastName=LI, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=2, address=2 College of Materials Science and Engineering, Nanjing Tech University , Nanjing 211816, China, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null), CN=AuthorExt(id=1329514634517221870, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, authorId=1329514634408169963, language=CN, stringName=李峰, firstName=null, middleName=null, lastName=null, prefix=null, suffix=null, authorComment=null, nameInitials=null, affiliation=null, department=null, xref=2, address=2 南京工业大学 材料科学与工程学院 , 南京 211816, bio=null, bioImg=null, bioContent=null, aboutCorrespAuthor=null)}, companyList=[AuthorCompany(id=1329514633854521816, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, xref=2, ext=[AuthorCompanyExt(id=1329514633871299033, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633854521816, language=EN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=2 College of Materials Science and Engineering, Nanjing Tech University , Nanjing 211816, China), AuthorCompanyExt(id=1329514633883881946, tenantId=1045748351789510663, journalId=1155139928303341741, articleId=1329505214697390374, companyId=1329514633854521816, language=CN, country=null, province=null, city=null, postcode=null, companyName=null, departmentName=null, remark=2 南京工业大学 材料科学与工程学院 , 南京 211816)])])]
刘同纲,郑成思,张明亚,李峰.
焊接方式对 304/201/304 不锈钢复合板搭接接头组织与性能的影响[J].
安徽工业大学学报(自然科学版), 2026, 43(5): 575-588 DOI:10.12415/j.issn.1671−7872.26051
| [1] |
LIU Z, GUO Z, RAO X, et al. A comprehensive review on the material performance affected by gaseous alternative fuels in internal combustion engines[J]. Engineering Failure Analysis, 2022, 139: 106507.
|
| [2] |
SHAHABUDDIN M, MOFIJUR M, SHUVHO M B A, et al. A study on the corrosion characteristics of internal combustion engine materials in second—generation jatropha curcas biodiesel[J]. Energies, 2021, 14(14): 4352.
|
| [3] |
HOANG A T, TABATABAEI M, AGHBASHLO M. A review of the effect of biodiesel on the corrosion behavior of metals/alloys in diesel engines[J]. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 2020, 42(23): 2923-2943.
|
| [4] |
LIU B X, WANG S, FANG W, et al. Meso and microscale clad interface characteristics of hot—rolled stainless steel clad plate[J]. Materials Characterization, 2019, 148: 17-25.
|
| [5] |
HU X, YANG Y, SONG M. Experimental and numerical investigations on the thermomechanical behavior of 304 stainless steel/Q345R composite plate weld joint[J]. Materials, 2019, 12(21): 3489.
|
| [6] |
FARZAD B, HOSSEIN M, MAHDI R, et al. Dissimilar joining of duplex AISI 2304 stainless steel/austenitic AISI 321 stainless steel using resistance spot welding technique: microstructural evolutions, tensile—shear properties, and fracture analysis[J]. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2024, 238(12): 5685-5698.
|
| [7] |
FUKUMOTO S, FUJIWARA K, TOJI S, et al. Small—scale resistance spot welding of austenitic stainless steels[J]. Materials Science and Engineering: A, 2008, 492(1/2): 243-249.
|
| [8] |
LIU Y, XIE Y, SUN X, et al. Indentation—free resistance spot welding of SUS301L stainless steel[J]. Metals, 2024, 14(10):1178.
|
| [9] |
NING J, NA S J, WANG C, et al. A comparison of laser—metal inert gas hybrid welding and metal inert gas welding of high—nitrogen austenitic stainless steel[J]. Journal of Materials Research and Technology, 2021, 13: 1841-1854.
|
| [10] |
TANG M, LI T, ZHAO P. Effect of the laser welding thermal process on the microstructure evolution and corrosion resistance of deformed austenitic stainless steel joints[J]. Journal of Materials Science, 2025, 60(6): 3129-3147.
|
| [11] |
GOU N N, ZHANG J X, ZHANG L J, et al. Single pass fiber laser butt welding of explosively welded 2205/X65 bimetallic sheets and study on the properties of the welded joint[J]. The International Journal of Advanced Manufacturing Technology, 2016, 86(9): 2539-2549.
|
| [12] |
COSTANZA G, GIUDICE F, MISSORI S, et al. An overview of the working conditions of laser—arc hybrid processes and their effects on steel plate welding[J]. Journal of Manufacturing and Materials Processing, 2025, 9(8): 248.
|
| [13] |
许芙蓉. 高强钢激光−电弧复合焊研究进展[J]. 机械研究与应用, 2025, 38(5): 175-177,182.
|
| [14] |
XU F R. Research progress on laser−arc hybrid welding of high—strength steel[J]. Mechanical Research & Application, 2025, 38(5): 175-177,182.
|
| [15] |
MEKONONE S T, GEMECHU T G, MEKONNEN T H, et al. Optimization, thermo—mechanical loading effects and microstructure evolutions of metal inert gas (MIG) welded 304L stainless steel[J]. Materials Today Communications, 2025, 42: 111514.
|
| [16] |
LI C, DUAN C, QI Y, et al. Effect of shielding gas on MIG welding performance with austenitic wire[J]. Materials Letters, 2023, 339: 134118.
|
| [17] |
MADAVI K R, JOGI B F, LOHAR G S. Metal inert gas (MIG) welding process: a study of effect of welding parameters[J]. Materials Today:Proceedings, 2022, 51: 690-698.
|
| [18] |
李小兵, 束长荣, 陆立婷, 等. 不锈钢复合板的焊接工艺研究现状及进展[J]. 中国冶金, 2025, 35(1): 15-31.
|
| [19] |
LI X B, SHU C R, LU L T, et al. Research status and progress of welding technology for stainless steel clad plates[J]. China Metallurgy, 2025, 35(1): 15-31.
|
| [20] |
YANG Z, YANG Z, WANG Z, et al. Synergy in toughening: the comprehensive influence of nickel on microstructure and hydrogen embrittlement resistance of X65MH welds[J]. Corrosion Science, 2026, 258: 113373.
|
| [21] |
张学刚, 郭旭超, 焦帅杰, 等. 奥氏体不锈钢焊缝金属 σ 相析出及其对性能影响[J]. 焊接学报, 2025, 46(5): 105-112.
|
| [22] |
ZHANG X G, GUO X C, JIAO S J, et al. Sigma phase precipitation in austenitic stainless steel weld metal and its effect on properties[J]. Transactions of the China Welding Institution, 2025, 46(5): 105-112.
|
| [23] |
冯梦楠, 罗震, 李洋, 等. 电阻点焊熔核微观组织模拟[J]. 焊接学报, 2015, 36(8): 31-34,114.
|
| [24] |
FENG M N, LUO Z, LI Y, et al. Simulation of microstructure in resistance spot welding nugget[J]. Transactions of the China Welding Institution, 2015, 36(8): 31-34,114.
|
| [25] |
张良, 闫飞. GH909 合金激光焊接接头的微观组织特征[J]. 中国激光, 2022, 49(8): 40-48.
|
| [26] |
ZHANG L, YAN F. Microstructure characteristics of laser welded joint of GH909 alloy[J]. Chinese Journal of Lasers, 2022, 49(8): 40-48.
|
| [27] |
ZHAO Y, LU Y, LUO Y, et al. Microstructure evolution and fracture behavior of dissimilar friction stir welding of 1060Al alloy to AZ31B Mg alloy[J]. Materials Characterization, 2021, 180: 111440.
|
| [28] |
YU L, NISHIMOTO K, HIRATA H, et al. Hardness prediction of the heat—affected zone in multilayer welded SUS316 stainless steel based on dislocation density change behavior[J]. Metallurgical and Materials Transactions A, 2024, 55(6): 1788-1803.
|
| [29] |
XIA X, WU J, LIU Z, et al. EBSD analysis of 316L stainless steel weldment on fusion reactor vacuum vessel[J]. Transactions of the Indian Institute of Metals, 2023, 76(12): 3379-3391.
|
| [30] |
ZHANG G, TONG X, WU G, et al. Research on the post—weld heat treatment of TIG repair welded joint of sand—cast Mg−Y−RE−Zr alloy[J]. Materials Science and Engineering: A, 2021, 821: 141577.
|
| [31] |
EGHLIMI A, SHAMANIAN M, ESKANDARIAN M, et al. Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by austenitic filler metal[J]. Materials Characterization, 2015, 106: 208-217.
|
| [32] |
CORDERO Z C, KNIGHT B E, SCHUH C A. Six decades of the Hall−Petch effect—a survey of grain—size strengthening studies on pure metals[J]. Internationals Materials Rwviews, 2016, 61(8): 495-512.
|
| [33] |
HALL E O. Variation of hardness of metals with grain size[J]. Nature, 1954, 173(4411): 948-949.
|
| [34] |
WANG W, LIU T G, CAO X Y, et al. In—situ SEM study of crack initiation and propagation behavior in a dissimilar metal welded joint[J]. Materials Science and Engineering: A, 2018, 729: 331-339.
|
| [35] |
MAO K, WANG H, WU Y, et al. Microstructure—property relationship for AISI 304/308L stainless steel laser weldment[J]. Materials Science and Engineering: A, 2018, 721: 234-243.
|
| [36] |
NASKAR A, BHATTACHARYYA M, RAJA K S, et al. Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions[J]. Corrosion Engineering, Science and Technology, 2022, 57(7): 599-612.
|
基金资助
安徽省科技攻关计划项目(202423i08050031)