高速离心泵启动过程瞬态特性优化

康俊杰 ,  潘余程 ,  马怡冉 ,  王彦伟

齐鲁工业大学学报 ›› 2026, Vol. 40 ›› Issue (5) : 72 -80.

PDF (13224KB)
齐鲁工业大学学报 ›› 2026, Vol. 40 ›› Issue (5) : 72 -80. DOI: 10.16442/j.cnki.qlgydxxb.2026.05.008
机电与信息工程

高速离心泵启动过程瞬态特性优化

作者信息 +

Multi-objective optimization of transient characteristics of high-speed centrifugal pump during startup period

Author information +
文章历史 +
PDF (13540K)

摘要

针对高速离心泵启动过程中扬程与效率的波动问题,开展了启动过程瞬态特性的多目标优化研究。首先,通过稳态实验验证了所建立的几何模型、网格划分方案及湍流模型的准确性,在此基础上对启动过程进行瞬态 CFD 仿真。采用拉丁超立方抽样生成 100 组设计样本,结合参数敏感性分析,确定叶轮进口直径、叶轮出口宽度、叶轮直径等 5 个参数为关键设计变量。随后,基于克里金模型分别建立扬程/效率波动最大值(ΔHmax/Δηmax)及平均值(Havg/ηavg)的代理模型,并采用 NSGA-Ⅱ多目标遗传算法进行优化。优化结果表明,相较于初始设计,ΔHmax降低 10.6%,Δηmax下降 18.75%,同时 Havg提升 5.47%,ηavg提升 1.645%。该优化不仅改善了启动过程的稳定性,也提升了泵的整体性能,为高速离心泵的设计提供了参考。

Abstract

A study on multi-objective optimization of transient characteristics during the startup process of high-speed centrifugal pumps was conducted to address the fluctuations in head and efficiency. First, the accuracy of the established geometric model, mesh partitioning scheme, and turbulence model was verified through steady-state experiments. Based on this, transient CFD simulations were performed for the startup process. Using Latin Hypercube Sampling, 100 sets of design samples were generated. Combined with parameter sensitivity analysis, five parameters, including the impeller inlet diameter, impeller outlet width, and impeller diameter, were identified as key design variables. Subsequently, surrogate models for the maximum fluctuations in head and efficiency(ΔHmax/Δηmax) and their average values(Havg/ηavg) were established based on the Kriging model, and optimization was carried out using the NSGA-II multi-objective genetic algorithm. The optimization results indicate that, compared with the initial design, ΔHmax was reduced by 10.6%, Δηmax decreased by 18.75%, while Havg increased by 5.47% and ηavg improved by 1.645%. This optimization not only enhances the stability of the startup process but also improves the overall performance of the pump, providing a reference for the design of high-speed centrifugal pumps.

关键词

高速离心泵 / 启动过程 / 瞬态特性 / 克里金模型 / 多目标优化

Key words

high-speed centrifugal pump / startup period / transient characteristics / Kriging model / multi-objective optimization

引用本文

引用格式 ▾
康俊杰,潘余程,马怡冉,王彦伟. 高速离心泵启动过程瞬态特性优化[J]. 齐鲁工业大学学报, 2026, 40(5): 72-80 DOI:10.16442/j.cnki.qlgydxxb.2026.05.008

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

姚志峰, 王福军, 杨敏, 等. 叶轮形式对双吸离心泵压力脉动特性影响试验研究[J]. 机械工程学报, 2011, 47(12): 133-137.

[2]

李志峰, 吴大转, 王乐勤. 圆柱和直桨叶突然启动瞬态流动的数值研究[J]. 工程热物理学报, 2007, 28(6): 945-947.

[3]

鲁阳平, 马灿, 谭磊, 等. 混流泵启动过程瞬态性能理论模型[J]. 清华大学学报(自然科学版), 2022, 62(12): 1938-1944.

[4]

曾桂陶. 混流泵快速启动过程瞬态流体激励与振动特性研究[D]. 杭州: 浙江大学, 2024.

[5]

马晓堂, 王宾, 宋文武. 离心泵启动过程内部流动特性分析[J]. 中国农村水利水电, 2021(10): 196-200.

[6]

李明慧, 刘厚林, 谈明高, 等. 导叶叶片数对喷水推进泵瞬态特性的影响[J]. 排灌机械工程学报, 2024, 42(1): 14-20.

[7]

何峻, 符杰, 钟卫, 等. 粒径对高比转速离心泵瞬态流动特性的影响[J]. 热能动力工程, 2022, 37(2): 38-45.

[8]

宋微, 冯子明, 方欣, 等. 潜油离心泵旋转速度对流道内瞬态气液两相流场影响[J]. 机床与液压, 2021, 49(13): 146-152.

[9]

范飞, 符杰, 王兴林, 等. 颗粒直径及浓度对高速离心泵非定常特性的影响[J]. 热能动力工程, 2021, 36(4): 30-36.

[10]

任映霖, 李帅, 王威, 等. 瞬态流体激励下离心泵转子振动特性研究[J]. 化工机械, 2023, 50(4): 516-522.

[11]

Chalgoum I, Elaoud S, Akrouit M, et al. Transient behavior of a centrifugal pump during starting period[J]. Applied Acoustics, 2016, 109: 82-89.

[12]

Shim H S, Kim K Y. Design optimization of the impeller and volute of a centrifugal pump to improve the hydraulic performance and flow stability[J]. Journal of Fluids Engineering, 2020, 142(10): 101211.

[13]

Yakhot V, Smith L M. The renormalization group, the ε-expansion and derivation of turbulence models[J]. Journal of Scientific Computing, 1992, 7: 35-61.

[14]

王衍, 王达, 胡琼, 等. 基于 CFD 的 T 形槽气膜密封网格无关性分析[J]. 润滑与密封, 2018, 43(11): 70-73.

[15]

Li Wei, Yang Qiaoyue, Yang Yi, et al. Optimization of pump transient energy characteristics based on response surface optimization model and computational fluid dynamics[J]. Applied Energy, 2024, 362: 123038.

[16]

张伟, 李斌, 李嘉, 等. 基于 Kriging 模型及双重搜索策略的燃油离心叶轮优化设计[J/OL]. 北京航空航天大学学报, 2025-11-01. https://doi.org/10.13700/j.bh.1001-5965.2025.0354.

[17]

Zhang Yu, Hu Sanbo, Wu Jinglai, et al. Multi-objective optimization of double suction centrifugal pump using Kriging metamodels[J]. Advances in Engineering Software 2014, 74: 16-26.

[18]

Dong Xiaolan, Liu Yang. Optimization design of the impeller structure for a micro centrifugal pump based on pressure pulsation and shear stress analysis[J]. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy 2025, 239(4): 609-623.

[19]

Kleijnen J P C. Kriging metamodeling in simulation: A review[J]. European Journal of Operational Research, 2009, 192(3): 707-716.

[20]

邵孟伟, 袁世飞, 周宏志, 等. 基于 BP 神经网络和遗传算法的翅片管结构优化[J]. 山东大学学报(工学版), 2025, 55(6): 76-82.

[21]

Li Anda, He Zhen, Zhang Yang. Bi-objective variable selection for key quality characteristics selection based on a modified NSGA-II and the ideal point method[J]. Computers in Industry, 2016, 82: 95-103.

基金资助

国家自然科学基金项目(52301337)

武汉工程大学研究生基金项目(CX2024431)

AI Summary AI Mindmap
PDF (13224KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉