跨厂区MTBE管线穿路段地埋管施工总结

于嘉慧 ,  缴万松 ,  吴海杰

工程设计与施工 ›› 2026, Vol. 8 ›› Issue (3) : 10 -13.

PDF (1770KB)
工程设计与施工 ›› 2026, Vol. 8 ›› Issue (3) : 10 -13. DOI: 10.12349/edc.v8i3.9817

跨厂区MTBE管线穿路段地埋管施工总结

作者信息 +

Summary of Cross-Plant MTBE Pipeline Buried Pipe Construction for Road Crossing Sections

Author information +
文章历史 +
PDF (1812K)

摘要

厂际 MTBE 管线直径 DN500,总长 3.8 km,跨越三个厂区,其中穿道路及厂区的 13 个点均采用埋地敷设,埋深约 2.4 m,平均穿越长度约 13 m,并设置 28 吋套管进行保护,配置阴极保护装置,与地上管线通过 45° 弯头顺接过渡。由于沿线地下附属管线及构筑物错综复杂,既无法采用顶管法,也不具备定向钻进条件,只能在场地严重受限、交通组织要求严格的前提下,采取分段开挖的施工方式。工程根据不同厂区的地质条件、地下障碍分布及现有生产装置运行情况,优化管线路由,现场实测放线后进行分段预制、组对及安装,同时对套管、保温、防腐及阴极保护等进行一体化施工控制。通过合理安排施工顺序、细化支护与降排水措施、强化安全与文明施工管理,确保了 MTBE 管线在多厂区、多交叉口条件下安全、优质、高效完成,为类似厂际长距离成品介质输送管线的穿路埋地施工提供了可借鉴的工程经验。

Abstract

The inter-factory MTBE pipeline has a diameter of DN500 and a total length of 3.8 km, spanning three factory areas. Among these, 13 points crossing roads and factory zones are buried underground at a depth of approximately 2.4 m, with an average crossing length of about 13 m. A 28-inch casing is installed for protection, and cathodic protection devices are configured. The pipeline transitions smoothly to above-ground sections via 45° elbows. Due to the complex network of underground utility lines and structures along the route, neither pipe jacking nor directional drilling methods are feasible. Consequently, the only viable approach under severely constrained site conditions and stringent traffic organization requirements is segmented excavation. The project optimized pipeline routing based on geological conditions, underground obstructions, and operational status of existing production facilities. After on-site surveying and marking, segmented prefabrication, assembly, and installation were carried out. Integrated construction control was implemented for casings, insulation, anti-corrosion, and cathodic protection. By arranging construction sequences rationally, refining support and drainage measures, and strengthening safety and civilized construction management, the MTBE pipeline was completed safely, with high quality and efficiency across multiple factory areas and intersections. This project provides valuable engineering experience for similar long-distance inter-factory finished product medium pipelines involving road crossings and underground installation.

关键词

埋地 / 套管 / 施工

Key words

Buried / Casing / Construction

引用本文

引用格式 ▾
于嘉慧,缴万松,吴海杰. 跨厂区MTBE管线穿路段地埋管施工总结[J]. 工程设计与施工, 2026, 8(3): 10-13 DOI:10.12349/edc.v8i3.9817

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

SY/T 0414-2007, 钢质管道聚乙烯胶粘带防腐层技术标准, 2007.

[2]

GB/T 21447-2018, 钢质管道外腐蚀控制规范, 2018.

[3]

SH/T 3501-2021, 石油化工有毒、可燃介质钢制管道工程施工及验收规范, 2021.

AI Summary AI Mindmap
PDF (1770KB)

0

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉