安全阀排放反力计算方法概述

武召阳 ,  马静 ,  张翔宇 ,  仝一然

工程设计与施工 ›› 2026, Vol. 8 ›› Issue (8) : 13 -16.

PDF (1579KB)
工程设计与施工 ›› 2026, Vol. 8 ›› Issue (8) : 13 -16. DOI: 10.12349/edc.v8i8.11439

安全阀排放反力计算方法概述

作者信息 +

Overview of Calculation Methods for Safety Valve Reaction Force

Author information +
文章历史 +
PDF (1616K)

摘要

安全阀排放反力是泄压系统管道及承重支架设计的核心载荷参数,其计算准确性直接关系到系统运行安全与结构完整性。本文系统梳理了API 520、ASME B31.1、HG/T 20570、AD 2000:A2、ISO 4126及《实用阀门设计手册》等国内外主流标准规范中安全阀排放反力的计算方法。各标准中的排放反力均以动量定理为理论基础,但在状态参数的确定路径上呈现差异:API 520与HG/T 20570(后者参照前者)以滞止压力和滞止比容为计算起点;ASME B31.1利用滞止焓进行推导;ISO 4126则形成涵盖气体、蒸汽、液体及两相流的完整计算框架;AD 2000 A2给出可用于可压缩和不可压缩介质的通用基础计算公式和包含静压推力的音速排放修正排放反力公式。通过对比公式结构、参数定义及适用的临界及亚临界流动边界,本文揭示了不同方法之间的内在关联与本质差异,旨在为工程实践中计算方法的合理选择提供理论参考。

Abstract

The reaction force generated during safety valve discharge serves as a core load parameter for the design of pressure relief system piping and load-bearing supports, and the accuracy of its calculation is directly tied to the system’s operational safety and structural integrity. This paper systematically sorts out the calculation methods for safety valve discharge reaction force specified in major domestic and international mainstream standards and specifications, including API 520, ASME B31.1, HG/T 20570, AD 2000:A2, ISO 4126, and the Practical Valve Design Manual. While all the discharge reaction force calculation methods defined in these standards are theoretically based on the momentum theorem, they differ in the paths for determining state parameters: API 520 and HG/T 20570 (the latter references the former) take stagnation pressure and stagnation specific volume as the starting point for calculation; ASME B31.1 conducts derivation using stagnation enthalpy; ISO 4126 has established a complete calculation framework covering gas, steam, liquid and two-phase flow; AD 2000 A2 provides a general basic calculation formula applicable to both compressible and incompressible media, as well as a corrected discharge reaction force formula for sonic discharge that incorporates static thrust. By comparing the formula structures, parameter definitions, and applicable critical and subcritical flow boundaries, this paper reveals the internal correlations and essential differences between different methods, aiming to provide a theoretical reference for the reasonable selection of calculation methods in engineering practice.

关键词

安全阀 / 排放反力 / 临界流动 / 亚临界流动

Key words

safety valve / discharge reaction force / critical flow / subcritical flow

引用本文

引用格式 ▾
武召阳,马静,张翔宇,仝一然. 安全阀排放反力计算方法概述[J]. 工程设计与施工, 2026, 8(8): 13-16 DOI:10.12349/edc.v8i8.11439

登录浏览全文

4963

注册一个新账户 忘记密码

参考文献

[1]

API RP520, Sizing, Selection, and Installation of Pressure-Relieving Device in Part Ⅱ-Installation[S]. Washington: American Petroleum Institute.

[2]

CCPS, Guidelines for Pressure Relief and Effluent Handling Systems, 2nd Edition, 2017, American Institute of Chemical Engineers, Center for Chemical Process Safety, 3 Park Avenue, 19th Floor, New York, New York 10016, www.aiche.org/ccps, ISBN 978-0-470-76773-3.

[3]

陆培文。 实用阀门设计手册[M]。 机械工业出版社, 2012.

[4]

HG/T20570[S]. 化工装置工艺系统工程设计技术规定, 1995.

[5]

ISO 4126-9[S]. Safety devices for protection against excessive pressure-Part9:Application and installation of safety devices excluding stand-along bursting disc safety devices,2008.

[6]

AD 2000-Merkblatt A2[S]. Safety devices against excess pressure-Safety valves 2015.

[7]

ASME B31.1, Power Piping[S]. New York: The American Society of Mechanical Engineers, 2020.

AI Summary AI Mindmap
PDF (1579KB)

5

访问

0

被引

详细

导航
相关文章

AI思维导图

/

〈 〉